Kodak I250 User Guide - Page 17

Making connections, Installing the IEEE-1394 (FireWire) card in the host computer - scanner driver

Get Kodak I250 - Document Scanner PDF manuals and user guides View all Kodak I250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Making connections Installing the IEEE-1394 (FireWire) card in the host computer Installing the Kodak Driver software Installing the IEEE-1394 (FireWire) cable Follow the instructions for installing the IEEE-1394 (FireWire) card and the Kodak Driver Software before you plug the scanner into the host computer. IMPORTANT: You must install the software on the host computer before you install the scanner. An IEEE-1394 six-pin connector is provided on the rear panel of the scanner for IEEE-1394 (FireWire) connectivity. 1. Install the IEEE-1394 (FireWire) card in the host computer as described by the instructions included with the card. IMPORTANT: Use proper precautions to avoid static when you install the IEEE-1394 (FireWire) card in your computer. 2. Power up the host computer after the IEEE-1394 (FireWire) card installation is complete. 1. Insert the Kodak i200 Series Installation CD in the CD-ROM drive. The installation program starts automatically. 2. Follow the onscreen instructions to install the TWAIN and ISIS drivers and the Kodak Scan Validation Tool. 1. Attach the beaded end of the IEEE-1394 (FireWire) cable to the IEEE-1394 port on the back of the scanner. WARNING: Make sure that the position of the IEEE-1394 (FireWire) cable connector end correlates to the IEEE-1394 port configuration before you plug the cable in. Damage to the scanner will occur if the cable is attached in the wrong position. IMPORTANT: Only use the IEEE-1394 cable that is supplied with the i200 Series Scanner. A-61167 April 2005 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
A-61167
April 2005
13
Making connections
Follow the instructions for installing the IEEE-1394 (FireWire) card and the
Kodak
Driver Software before you plug the scanner into the host computer.
IMPORTANT: You must install the software on the host computer before you
install the scanner.
Installing the IEEE-1394
(FireWire) card in the
host computer
An IEEE-1394 six-pin connector is provided on the rear panel of the scanner
for IEEE-1394 (FireWire) connectivity.
1.
Install the IEEE-1394 (FireWire) card in the host computer as described by
the instructions included with the card.
IMPORTANT: Use proper precautions to avoid static when you install the
IEEE-1394 (FireWire) card in your computer.
2.
Power up the host computer after the IEEE-1394 (FireWire) card
installation is complete.
Installing the
Kodak
Driver software
1.
Insert the
Kodak
i200 Series Installation CD in the CD-ROM drive.
The installation program starts automatically.
2.
Follow the onscreen instructions to install the TWAIN and ISIS drivers and
the Kodak Scan Validation Tool.
Installing the IEEE-1394
(FireWire) cable
1.
Attach the beaded end of the IEEE-1394 (FireWire) cable to the IEEE-1394
port on the back of the scanner.
WARNING:
Make sure that the position of the IEEE-1394 (FireWire) cable
connector end correlates to the IEEE-1394 port configuration
before you plug the cable in. Damage to the scanner will
occur if the cable is attached in the wrong position.
IMPORTANT: Only use the IEEE-1394 cable that is supplied with the
i200 Series Scanner.