Konica Minolta KIP 7970 KIP 7970 User Manual - Page 20

Environmental Condition - Correction, Turn on the Dehumidify Heater.

Get Konica Minolta KIP 7970 PDF manuals and user guides View all Konica Minolta KIP 7970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

1. 7. 4 Environmental Condition - Correction Take a necessary treatment according to the environmental condition as shown below. Humidity(%) Low 40% 70% High Possible problem "Void of image", "crease of paper" and other problems occurs when you print with plain paper and vellum. "Void of image" occurs when you print with vellum. "Void of image" occurs when you print with plain paper and vellum. "Void of image", "crease of paper" and other problems occurs when you print with plain paper and vellum. Necessary treatment 1. Install the humidifier in the room, and humidify the room air. 2. Remove the media from the machine right after the completion of print, and keep it in a plastic bag. If you will not make print soon, remove the vellum from the machine and keep it in a plastic bag. Remove the paper from the machine after everyday use, and keep it in a plastic bag. If you will not make print soon, remove the media from the machine and keep it in a plastic bag. 1. Turn on the Dehumidify Heater. 2. Remove the media from the machine right after the completion of print, and keep it in a plastic bag. NOTE (1) KIP 7970 is equipped with the Dehumidify Heater. Using it in high humidity environment (65% or higher) is recommended. Refer to [2.7 Dehumidifying Roll Media]. (2) "Void of image" and "crease of paper" will occur in case of extremely high or low humidity. Normal Print Crease of paper If the media is humidified; Normal Print Loss of image If the media is humidified; (continued on the next page) 1-13 Chapter 1 Before Use

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Chapter 1
Before Use
1-13
1. 7. 4
Environmental Condition - Correction
Take a necessary treatment according to the environmental condition as shown below.
Humidity(%)
Possible problem
Necessary treatment
Low
40%
70%
High
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and vellum.
1. Install the humidifier in the room, and
humidify the room air.
2. Remove the media from the machine
right after the completion of print, and
keep it in a plastic bag.
“Void of image” occurs when you print
with vellum.
If you will not make print soon, remove
the vellum from the machine and keep it
in a plastic bag.
Remove the paper from the machine after
everyday use, and keep it in a plastic bag.
“Void of image” occurs when you print
with plain paper and vellum.
If you will not make print soon, remove
the media from the machine and keep it in
a plastic bag.
“Void of image”, “crease of paper” and
other problems occurs when you print
with plain paper and vellum.
1. Turn on the Dehumidify Heater.
2. Remove the media from the machine
right after the completion of print, and
keep it in a plastic bag.
NOTE
(1) KIP 7970 is equipped with the Dehumidify Heater.
Using it in high humidity environment (65% or higher) is recommended.
Refer to [2.7
Dehumidifying Roll Media].
(2) “Void of image” and “crease of paper” will occur in case of extremely high or low humidity.
(continued on the next page)
Normal Print
Normal Print
If the media is humidified;
If the media is humidified;
Crease of paper
Loss of image