Konica Minolta bizhub PRO 1100 bizhub PRO 1100 Safety Information Guide - Page 10

bizhub PRO 1100

2-3

2.1

Warnings and Precautions

2

2.1

Warnings and Precautions

2.1.1

Power Source Connection

Do not use any power cord other than the one supplied in the

package or attached on the products. If a power cord is not

supplied, use only the power cord and plug that are specified

in the user documentation. Failure to use this cord could re-

sult in a fire or electrical shock. If the power cord supplied in

the package cannot be used in the country where this prod-

uct was sold, use a power cord that meets the following con-

ditions or contact your Technical Representative.

•

The power cord has voltage and current rating appropri-

ate for the rating plate on this machine.

•

The power cord meets regulatory requirements for the ar-

ea.

•

The power cord is provided with grounding pin/terminal.

Do not use the power cord to other products.

Failure to do that could result in a fire or electrical shock.

Do not scratch, abrade, place a heavy object on, heat, twist,

bend, step on, pull on, or damage the power cord. Use of a

damaged power cord (exposed core wire, broken wire, etc.)

could result in a fire or breakdown.

Should any of these conditions be found, immediately turn

OFF the power switch, unplug the power cord from the pow-

er outlet, and then call your authorized service representa-

tive.

Do not use the power source voltage other than being spec-

ified on the machine. Failure to do that could result in a fire or

electrical shock.

Do not use a multiple outlet adapter to connect any other ap-

pliances or machines. Use of a power outlet for more than the

marked current value could result in a fire or electrical shock.

Do not use an extension cord. Use of an extension cord could

cause a fire or electric shock. If the power cord furnished with

the product is not long enough to be plugged into a wall out-

let, contact your Technical Representative.

Do not unplug and plug in the power cord with a wet hand,

as an electrical shock could result.

Plug the power cord all the way into the power outlet. Failure

to do this could result in a fire or electrical shock.

Make sure to ground this product.(Connect the power cord

to an electrical outlet that is equipped with a grounding ter-

minal.) Failure to do so and an unlikely event of leakage could

result in a fire or electrical shock.

Section	Page
Contents	2
1 Introduction	5
1.1 Welcome	5
1.1.1 Configuration and Usage of this Guide	5
1.2 Environmental Information	6
1.3 Legal Restrictions on Reproduction	7
2 Safety Information	9
2.1 Warnings and Precautions	10
2.1.1 Power Source Connection	10
2.1.2 Installation	11
2.1.3 Using the Product	12
2.1.4 Consumables	13
2.2 Regulation Notices	15
2.2.1 Ozone Release	15
2.2.2 Electromagnetic Interference and Safety Approvals	15
2.3 Warning and Caution Labels	17
2.3.1 Caution Labels on Fusing Part of Conveyance Fixing Unit	17
2.3.2 Caution Labels on the Front of Internal Main Body and Conveyance Fixing Unit	18
2.3.3 Warning Label on Waste Toner Box	19
2.3.4 Caution Labels on Finisher FS-532	20
2.3.5 Caution Labels on Output Tray OT-507	22
2.3.6 Caution Labels on Multi Bypass Tray Unit MB-507	23
2.3.7 Warning Labels on Z-Folding Unit ZU-608	24
2.3.8 Caution Label on Large Capacity Unit LU-411/Large Capacity Unit LU-412	25
2.3.9 Warning Labels on Multi Puncher GP-501	26
2.3.10 Caution and Warning Labels on Auto Ring Binder GP-502	27
2.3.11 Warning Label for Grounding Applied on the Back of Main Body	29
2.4 Installation Space	30
2.5 Operation Precautions	34
2.5.1 Power Source	34
2.5.2 Operating Environment	34
2.5.3 Storage of Printed Materials	34
2.5.4 Ozone Release	34
2.5.5 Direct Sunlight	34
2.5.6 Authentication Unit AU-201/Authentication Unit AU-201S	34
2.5.7 Data Stored in This Machine	34

Konica Minolta bizhub PRO 1100 bizhub PRO 1100 Safety Information Guide - Page 10

Warnings and Precautions

Page 10 highlights