Kyocera FS-6525MFP Kyocera Command Center RX User Guide Rev-1.60 - Page 63

POP before SMTP Timeout, POP before SMTP

Get Kyocera FS-6525MFP PDF manuals and user guides View all Kyocera FS-6525MFP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Settings Pages Set the SMTP Port Number, or use the SMTP default port 25. Choose the default port number 465 for SMTP connections over SSL. SMTP Server Name Enter the SMTP server host name or its IP address. If entering the host name, rather than the IP address, a DNS server address must also be configured. The DNS server address may be entered on the TCP/IP General page (refer to Advanced > Protocols > TCP/IP > General on page 6-32). SMTP Server Timeout Sets the timeout in seconds during which this device tries to connect to the SMTP server. Authentication Protocol Enables or disables the SMTP authentication protocol or sets POP before SMTP as the authentication type. Authenticate as Specifies the user to be authenticated in SMTP authentication. When POP3 User 1 to 3 (Refer to Advanced > E-mail > POP3 > User # on page 6-41) and i-FAX User are set, you can select one of them. If you want to select a different user, select Other and enter the login account name and login password for authentication. Login User Name When Other is selected for Authenticate as, the account name set here will be used for SMTP authentication. Login Password When Other is selected for Authenticate as, the password set here will be used for authentication. SMTP Security Enables or disables the SMTP Security. When this protocol is enabled, either SSL/TLS or STARTTLS must be selected. To enable SMTP security, the SMTP port may have to be changed according to the server settings. Typically, 465 for SSL/TLS and 25 or 587 for STARTTLS are well-known SMTP ports. POP before SMTP Timeout Enter the timeout in seconds during which this machine tries to connect to the SMTP server when set POP before SMTP as the Authentication Protocol. Test Tests to confirm that the settings on this page are correct. When the Test button is pressed, this machine tries to connect to the SMTP server. E-mail Size Limit Enter the maximum size of E-mail that can be sent in Kilobytes. When the value is 0, the limitation for E-mail size is disabled. Sender Address Enter the E-mail address of the person responsible for the printing system, such as the printer administrator. A reply or non-delivery report will go to a person rather than to the machine. The sender address must be entered correctly for SMTP authentication. Note that no mail message can be sent unless the sender's address is specified. Signature COMMAND CENTER RX 6-39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Settings Pages
Set the SMTP Port Number, or use the SMTP default port 25. Choose the
default port number 465 for SMTP connections over SSL.
SMTP Server Name
Enter the SMTP server host name or its IP address. If entering the host
name, rather than the IP address, a DNS server address must also be
configured. The DNS server address may be entered on the
TCP/IP General
page (refer to
Advanced > Protocols > TCP/IP > General
on page 6-32).
SMTP Server Timeout
Sets the timeout in seconds during which this device tries to connect to the
SMTP server.
Authentication Protocol
Enables or disables the SMTP authentication protocol or sets
POP before
SMTP
as the authentication type.
Authenticate as
Specifies the user to be authenticated in SMTP authentication. When POP3
User
1
to
3
(Refer to
Advanced > E-mail > POP3 > User #
on page 6-41) and
i-FAX User
are set, you can select one of them. If you want to select a
different user, select
Other
and enter the
login account name
and
login
password
for authentication.
Login User Name
When
Other
is selected for
Authenticate as
, the account name set here will
be used for SMTP authentication.
Login Password
When
Other
is selected for
Authenticate as
, the password set here will be
used for authentication.
SMTP Security
Enables or disables the SMTP Security. When this protocol is enabled,
either
SSL/TLS
or
STARTTLS
must be selected. To enable SMTP security,
the SMTP port may have to be changed according to the server settings.
Typically, 465 for SSL/TLS and 25 or 587 for STARTTLS are well-known
SMTP ports.
POP before SMTP Timeout
Enter the timeout in seconds during which this machine tries to connect to
the SMTP server when set
POP before SMTP
as the
Authentication
Protocol
.
Test
Tests to confirm that the settings on this page are correct. When the
Test
button is pressed, this machine tries to connect to the SMTP server.
E-mail Size Limit
Enter the maximum size of E-mail that can be sent in Kilobytes. When the
value is 0, the limitation for E-mail size is disabled.
Sender Address
Enter the E-mail address of the person responsible for the printing system,
such as the printer administrator. A reply or non-delivery report will go to a
person rather than to the machine. The sender address must be entered
correctly for SMTP authentication. Note that no mail message can be sent
unless the sender's address is specified.
Signature
COMMAND CENTER RX
6-39