Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 19

IMPORTANT, Power switch, Face-up tray, Power cord, Document Processor connector

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Section 2 NAMES OF PARTS (23) (24) (21) (20) (22) (20) Power switch (Turn this switch ON ( | ) before copying.) (21) Face-up tray (Finished copies can be ejected and stored face-up on this tray. The face-up tray should be used when copying onto thick paper and other special paper. This tray has a storage capacity of 30 sheets of standard copy paper (80 g/m²) but only 1 sheet of special paper should be stored there at one time.) (22) Power cord (23) Document Processor connector (Attach the connection cable here when installing the optional Document Processor.) (24) Right cover anchor pin (This pin must be removed and the right cover opened in order to access the slot for installing additional memory. If you need to add additional memory, contact your service representative or an authorized service center.) IMPORTANT! • Be sure to hold both the front and rear sides of the copier when carrying it, as shown in the illustration. • Be sure not to pull the drawer out when holding the front of the copier. • Be sure that the original cover is closed whenever transporting the copier. • DO NOT attempt to carry the copier by holding only the top portion. Doing so may result in you dropping the copier and thereby damaging the copier and/or its covers. 2-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Section 2
NAMES OF PARTS
2-3
(20) Power switch
(Turn this switch ON ( | ) before copying.)
(21) Face-up tray
(Finished copies can be ejected and stored face-up on this tray.
The face-up tray should be used when copying onto thick
paper and other special paper. This tray has a storage
capacity of 30 sheets of standard copy paper (80 g/m²) but only
1 sheet of special paper should be stored there at one time.)
(22) Power cord
(23) Document Processor connector
(Attach the connection cable here when installing the optional
Document Processor.)
(24) Right cover anchor pin
(This pin must be removed and the right cover opened in order
to access the slot for installing additional memory. If you need
to add additional memory, contact your service representative
or an authorized service center.)
(20)
(21)
(22)
(23)
(24)
IMPORTANT!
•
Be sure to hold both the front and rear sides of the copier when carrying it, as shown in the illustration.
•
Be sure not to pull the drawer out when holding the front of the copier.
•
Be sure that the original cover is closed whenever transporting the copier.
•
DO NOT attempt to carry the copier by holding only the top portion. Doing so may result in you dropping the copier and thereby
damaging the copier and/or its covers.