LG 26LH1DC1 Operation Guide - Page 65
setting, TUNE MODE
View all LG 26LH1DC1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 65 highlights
Detailed Descriptions of Installer Menu Items 079 - UPN MSB-1 (UPN Most Significant Byte-1 ) User programmable numben most significant byte-1 readable by M.RI. command. Not linked to serial number. 092 - RGB2 ENABLE (Red-Green-Blue 2 Enable) Set to 1 to enable display panel Video 3 input for Composite Video, set to 2 to enable for S-Video. Set to 0 to disable display panel Video 3 input. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable numben most significant byte-2 readable by M.RI. command. Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable numben least significant byte readable by M.RI. command. Not linked to serial number. 082 - CHASM ERROR (Checksum Error) Enforces rigid M.RI. checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on M.RI. async port). SPI is always checked. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature, if available. Set to 0 to disable SAP feature. 096 - DEE ASR RATIO (Default Aspect Ratio) Selects default aspect ratio at power up, see settings below. Set to 0 for set by program. Set to 1 for 4:3. Set to 2 for 16:9 (Factory Default). Set to 4 for Zoom 1 Set to 5 for Zoom 2 102 - ATSC BAND 083 - HANDSHK TIME (Handshake Time) Sets up TV to receive different types of incoming signals: Adds an additional delay to the handshake time which is 0=Broadcast, 1 =CATV, 2=HRC, 3=IRC, 4=Same as 64 msec, thus relaxing M.RI. timing requirements to be NTSC. compatible with PC based Windows controlled systems, 103 - ATSC TUNE MODE N 0 range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time]). Selects ATSC tuning mode: 0=Virtual, 1 =Physical. *Note: The setting above is ignored if Installer item 102 ATSC r"rl 084 - PERMANENT BLK (Permanent Block) BAND, is set to 1 -CATV, 2-HRC or 3-1RC Then 103 - ATSC N Allows Lock (Parental Control) blocking schemes to be TUNE MODE above always resets itself to Physical (1), regardless permanent by disabling the blocking hours function. of what value appears for item 103 on the Installer menu. Set to 1 to install Parental Control restrictions 104 - START MINOR CHANNEL 0 permanently. Set to 0 for user-specified hours control of blocking Sets XX-XX minor starting channel at power up: r"rl schemes. 0=NTSC. If not 0, number selected is the Minor start channel number. 087 - REAR RGB EN. (Rear RGB1 Enable) Controls access to rear RGB1 input on display panel. Set to 1 to enable RGB1 input for DTV. Set to 0 to disable RGB1 input. *Note: The setting above is ignored if Installer item 093 RJP AVAILABLE, is set to 1. Then 087 - REAR RGB EN. above, always resets itself to PC (1) -- regardless of what value appears for item 087 on the Installer menu. 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power Off. Set to 0 to retain default aspect ratio with power Off. See item 96. Default Aspect Ratio above. 107 - BANNER SELECT Not applicable. 116 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for normal. Set to 1 for blank. 090 - KEY LOCK If set to 1, display panel keyboard is locked out, not available to end user. IR receiver remains functional. 091 - YPrPb2 EN. (Rear Component Video 2 Enable) Set to 1 to enable display panel Component 2 input. Set to 0 to disable display panel Component 2 input. 117 - FACT DEFAULT (Factory Default) Set to 0 for normal. Set to 1 to load default settings for all installer menu items. _ facAtoRrNy INGde:faSuletsttingandthcisleator th1ewicllharenlnoeald litshte including erasing any assigned Channel Icons and Labels. 65