LG 37LD330H Setup Guide - Page 19

Installer Menu (Cont.) 053 - DIS. CH-TIME (Disable Channel-Time) Set to 1 to disable the Channel-Time display; Channel-Time display will not appear. Set to 0 to enable the Channel-Time display. 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart: 0 = Black 3 = Cyan 6 = Yellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet Note: Applies only to "Channel Not Available" message if item 073 is set to 1 (enabled). If foreground color and background color are the same, the menu background will be transparent. 082 - CHKSM ERROR (Checksum Error) Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PCbased Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].) 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 071 - BCK. CH-TIME (Channel-Time Display Background Color) Set according to Color Chart: 0 = Black 3 = Cyan 6 = Yellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet Note: Applies only to "Channel Not Available" message if item 073 is set to 1 (enabled). If foreground color and background color are the same, the menu background will be transparent. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a onetime automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed. 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 073 - CH NOT AVBLE (Channel Not Available) If set to 1 and item 028 CH. OVERIDE is set to 0, a "NOT AVAILABLE" message is displayed when directly accessing a channel not in the channel scan list available in memory. 090 - KEY LOCK If set to 1, display panel Channel, Volume, and Captions buttons are disabled, Power button remains enabled. If set to 0, the Channel, Volume, Captions, and Power buttons are all enabled. 075 - REVERT CH (Revert to Start Channel) If set to 1 and loss of MPI communication occurs, TV automatically tunes to the specified Start Channel. 091 - YPrPb2 EN. (HDMI2 Enable) Set to 0 to disable display panel HDMI2 input. Set to 1 to enable DTV mode. Set to 2 to enable PC mode. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by MPI command. Note: Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by MPI command. Note: Not linked to serial number. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by MPI command. Note: Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by MPI command. Note: Not linked to serial number. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function Menu, if Function Menu is available. Set to 0 to disable SAP feature on Function Menu, if Function Menu is available. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up. • Set to 0 for Set By System. • Set to 1 for 4:3. • Set to 2 for 16:9 (Factory Default). • Set to 3 for Just Scan. • Set to 4 for Zoom. Note: Only applies if item 106 ASP RATIO LOCK is disabled, set to 0. 206-4185 19