LG 55EF5K-P User Guide - Page 94

Scan Inversion] Command: s n

Get LG 55EF5K-P PDF manuals and user guides View all LG 55EF5K-P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

ENGLISH 94 99. [Scan Inversion] (Command: s n, 87) It controls the on/off status of Scan Inversion. Transmission (s)(n)( )(Set ID)( )(8)(7)( )(Data)(Cr) Data 00: Off 01: On Acknowledgment (n)( )(Set ID)( )(OK/NG)(8)(7)(Data)(x) * This feature may not be available for all models. * If you change the values on a Video Wall model, please reboot for it to work normally. 100. [Frame Control] (Command: s n, b7) It controls the Frame Control. Transmission (s)(n)( )(Set ID)( )(b)(7)( )(Data)(Cr) Data 00: Off 01: On Acknowledgment (n)( )(Set ID)( )(OK/NG)(b)(7)(Data)(x) * This feature may not be available for all models. * If you change the values on a Video Wall model, please reboot for it to work normally. 102. Read Brightness Value (Command: m u) Checks the brightness value. Transmission (m)(u)( )(Set ID)( )(FF)(Cr) Acknowledgment (u)()(SetID)()(OK/NG)(Data1)(Data2)(Data3)(Data4) (Data5)(Data6)(Data7)(x) Data 1 00~64: Backlight PWM figure 0-100 Data 2 00~ff: The upper 1-byte of the value measured by the CA210. Data 3 00~ff: The lower 1-byte of the value measured by the CA210. The CA210 measurement is Hex: 0000~ffff, Decimal: 0 - 65535 Data 4 00~ff: The upper 1-byte of the value measured by BLU 1 Sensor. Data 5 00~ff: The lower 1-byte of the value measured by BLU 1 Sensor Data 6 00~ff: The upper 1-byte of the value measured by BLU 2 Sensor Data 7 00~ff: The lower 1-byte of the value measured by BLU 2 Sensor The BLU measurement is Hex: 0000~ffff, Decimal: 0 65535 * The CA210 measurement is entered as "Calibration" when the product is released from the factory. It is Default 0 before the calibration. * This feature may not be available for all models. 101. [Average Picture Level Auto Control] (Command: s n, be) Sets Average Picture Level Auto Control. Transmission (s)(n)( )(Set ID)( )(b)(e)( )(Data)(Cr) Data 00: [Off] 01: [On] Acknowledgment (n)( )(Set ID)( )(OK/NG)(b)(e)(Data)(x) * This feature may not be available for all models. 103. [Screen Fault Detection] (Command: t z) Sets the Screen Fault Detection feature. Transmission (t)(z)( )(Set ID)( )(Data)(Cr) Data 00: [Off] 01: [On] Acknowledgment (z)( )(Set ID)( )(OK/NG)(Data)(x) * This feature may not be available for all models. 104. [Stereo Mode] (Command: s n, c2) Controls Stereo Mode. Transmission (s)(n)( )(Set ID)( )(c)(2)( )(Data)(Cr) Data 00: Left/Right 01: Left/Left 02: Right/Right Acknowledgment (n)( )(Set ID)( )(OK/NG)(c)(2)(Data)(x) * This feature may not be available for all models.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
ENGLISH
94
99. [Scan Inversion] (Command: s n, 87)
It controls the on/off status of Scan Inversion.
Transmission
(s)(n)( )(Set ID)( )(8)(7)( )(Data)(Cr)
Data
00: Off
01: On
Acknowledgment
(n)( )(Set ID)( )(OK/NG)(8)(7)(Data)(x)
* This feature may not be available for all models.
* If you change the values on a Video Wall model, please reboot
for it to work normally.
100. [Frame Control] (Command: s n, b7)
It controls the Frame Control.
Transmission
(s)(n)( )(Set ID)( )(b)(7)( )(Data)(Cr)
Data
00: Off
01: On
Acknowledgment
(n)( )(Set ID)( )(OK/NG)(b)(7)(Data)(x)
* This feature may not be available for all models.
* If you change the values on a Video Wall model, please reboot
for it to work normally.
101. [Average Picture Level Auto Control] (Command: s
n, be)
Sets Average Picture Level Auto Control.
Transmission
(s)(n)( )(Set ID)( )(b)(e)( )(Data)(Cr)
Data
00: [Off]
01: [On]
Acknowledgment
(n)( )(Set ID)( )(OK/NG)(b)(e)(Data)(x)
* This feature may not be available for all models.
102. Read Brightness Value (Command: m u)
Checks the brightness value.
Transmission
(m)(u)( )(Set ID)( )(FF)(Cr)
Acknowledgment
(u)()(SetID)()(OK/NG)(Data1)(Data2)(Data3)(Data4)
(Data5)(Data6)(Data7)(x)
Data 1 00~64: Backlight PWM figure 0-100
Data 2 00~ff: The upper 1-byte of the value measured by
the CA210.
Data 3 00~ff: The lower 1-byte of the value measured by
the CA210.
The CA210 measurement is Hex: 0000~ffff, Decimal:
0 - 65535
Data 4 00~ff: The upper 1-byte of the value measured by
BLU 1 Sensor.
Data 5 00~ff: The lower 1-byte of the value measured by
BLU 1 Sensor
Data 6 00~ff: The upper 1-byte of the value measured by
BLU 2 Sensor
Data 7 00~ff: The lower 1-byte of the value measured by
BLU 2 Sensor
The BLU measurement is Hex: 0000~ffff, Decimal: 0 -
65535
* The CA210 measurement is entered as “Calibration” when
the product is released from the factory. It is Default 0 before
the calibration.
* This feature may not be available for all models.
103. [Screen Fault Detection] (Command: t z)
Sets the Screen Fault Detection feature.
Transmission
(t)(z)( )(Set ID)( )(Data)(Cr)
Data
00: [Off]
01: [On]
Acknowledgment
(z)( )(Set ID)( )(OK/NG)(Data)(x)
* This feature may not be available for all models.
104. [Stereo Mode] (Command: s n, c2)
Controls Stereo Mode.
Transmission
(s)(n)( )(Set ID)( )(c)(2)( )(Data)(Cr)
Data
00: Left/Right
01: Left/Left
02: Right/Right
Acknowledgment
(n)( )(Set ID)( )(OK/NG)(c)(2)(Data)(x)
* This feature may not be available for all models.