LG A916BM Owners Manual - Page 13

Installing the Charging, Station

Page 13 highlights

us_main.book.book Page 12 Tuesday, March 16, 2021 10:31 AM 12 INSTALLATION Installing the Charging Station WARNING • To prevent tipping, self-standing mode installations should be anchored to the wall using the provided stand anchoring screw, anchoring block and double-sided tape. • For drywall anchor: use 1/4″ (6.5 mm) drill bit • For concrete or wall stud: use 1/8″ (3 mm) drill bit • If screwing into drywall, use the drywall anchors. CAUTION • Do not allow children or pets to hang onto the charging station. They could be injured or cause damage to the appliance. • Take care not to drop the product parts while unpacking them to avoid appliance damage or personal injury. • Do not use double-sided tape to attach the charging station to wallpaper. The weight of the charging station and the product body could damage the paper. • Use the stand anchoring screw on concrete or solid walls. If the appliance is not anchored securely and falls, it could result in damage to property or the product. GU 3 Attach the charging station to the wall with the wall anchoring screws. NOTE • Once assembled, the floor stand dock and the floor stand pipe cannot be disassembled. • The cost of a service call to install or reinstall the charging station is not covered under the warranty. Wall-Mounted Installation For wall-mounted installations, the charging station must be attached securely to the wall using the provided (short) wall anchoring screws. • The detachable nozzle storage cannot be attached to the charging station in a wallmounted installation. 1 Connect the power adapter to the port on the back of the charging station. 2 Drill 2 holes and insert the drywall anchors (if needed) at least 3.25 ft (1 m) from the floor and near enough to easily reach a power outlet. • Before drilling, make sure that there are no pipes or electrical wires inside the wall at the desired location. 4 Plug the power cord into the power outlet. Self-Standing Installation Follow the steps below to install the charging station on a hard and level floor.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33

12
INSTALLATION
Installing the Charging
Station
WARNING
To prevent tipping, self-standing mode
installations should be anchored to the wall
using the provided stand anchoring screw,
anchoring block and double-sided tape.
CAUTION
Do not allow children or pets to hang onto the
charging station. They could be injured or cause
damage to the appliance.
Take care not to drop the product parts while
unpacking them to avoid appliance damage or
personal injury.
Do not use double-sided tape to attach the
charging station to wallpaper. The weight of the
charging station and the product body could
damage the paper.
Use the stand anchoring screw on concrete or
solid walls. If the appliance is not anchored
securely and falls, it could result in damage to
property or the product.
NOTE
Once assembled, the floor stand dock and the
floor stand pipe cannot be disassembled.
The cost of a service call to install or reinstall the
charging station is not covered under the
warranty.
Wall-Mounted Installation
For wall-mounted installations, the charging
station must be attached securely to the wall using
the provided (short) wall anchoring screws.
The detachable nozzle storage cannot be
attached to the charging station in a wall-
mounted installation.
1
Connect the power adapter to the port on the
back of the charging station.
2
Drill 2 holes and insert the drywall anchors (if
needed) at least 3.25 ft (1 m) from the floor
and near enough to easily reach a power
outlet.
Before drilling, make sure that there are no
pipes or electrical wires inside the wall at
the desired location.
For drywall anchor: use 1/4
(6.5 mm) drill
bit
For concrete or wall stud: use 1/8
(3 mm)
drill bit
If screwing into drywall, use the drywall
anchors.
3
Attach the charging station to the wall with
the wall anchoring screws.
4
Plug the power cord into the power outlet.
Self-Standing Installation
Follow the steps below to install the charging
station on a hard and level floor.
3.25 ft
us_main.book.book
Page 12
Tuesday, March 16, 2021
10:31 AM