LG AG-S350 Quick Start Guide - Page 6

Charging The Glasses, How To Wear The 3d Glasses, Using 3d Glasses

Page 6 highlights

ENGLISH USING 3D GLASSES Button Operation LED Indication Power On Press and hold the power button for 1 or 2 seconds. The red LED blinks once. Power Off Press and hold down the Power button (1 second ~2 second) The red LED blinks three times. Auto Off*1 The device is automatically switched off if there is no 3D signal for more than one minute. The red LED blinks three times. Battery(Lithium polymer) discharge 0 If the battery is discharged, the red LED blinks for 1 minute and turns off automatically. * When charging is completed, the LED is lit green. How to re-connect the glasses Press the power button for over eight seconds. Release the button when the green LED light turns on. Then, you will see the green light blink three times before the device is switched off. If you switch the power on again, the glasses will be connected to the TV with the strongest signal. -4# The Auto Off function automatically switches the power off when the glasses loose the signal from the TV. This may occur when the distance or angle between the device and the TV are out of range; when there is a barrier between the two devices; or when the device is switched from 3D to 2D mode. CHARGING THE GLASSES 1 Connect the USB port located under the power button on the glasses to the USB port of the TV or PC using the supplied 8-pin mini USB cable as shown by the figure. CAUTION ⶺ##Do not insert the supplied 8-pin mini USB cable in the reverse direction. Otherwise, this may cause damage to the product. H{1,#DJ0V683 2 Charge the glasses until the LED is green. The glasses will fully charge in about 1 hours 50 minute. ! NOTE ⶺ While charging: The LED is red. ⶺ When charging is complete: The LED is green. ⶺ When the battery is discharged: The Red LED blinks for 1 minute and turns off automatically. ⶺ The 3D glasses can still be used while charging via a USB device. CAUTION 君 If you use a USB cable other the one (8-pin mini USB) supplied with the product, the product may be damaged. 君 This equipment shall be powered with USB 2.0 or higher. ⶺ Avoid twisting or dropping the 3D glasses as this may cause damage or break them. 3 Battery life and charging time 君#5 min charge : Approximately 7 hours 君 30 min charge : Approximately 40 hours 叛#Battery life may vary depending on the user's environment. HOW TO WEAR THE 3D GLASSES Using 3D glasses may not be convenient for users wearing regular glasses. Adjusting the nose pad can improve your viewing comfort. How to adjust the nose pad 4 5 Pull the nose pad in the direction shown by the arrow as shown in the image. Be careful not to twist or lift the nose pad as this can cause damage. 6 ! NOTE ⶺ Follow the instructions in reverse order to put the nose pad back. ⶺ The nose pad can be adjusted even if you don't wear glasses.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

CHARGING THE GLASSES
1
Connect the USB port located under the power button on the glasses to the USB port of the
TV or PC using the supplied 8-pin mini USB cable as shown by the figure.
2
Charge the glasses until the LED is green.
The glasses will fully charge in about 1 hours 50
minute
.
3
Battery life and charging time
5 min charge : Approximately 7 hours
30 min charge : Approximately 40 hours
Battery life may vary depending on the user’s environment.
HOW TO WEAR THE 3D GLASSES
ENGLISH
CAUTION
Do not insert the supplied 8-pin mini USB cable in the reverse direction. Otherwise, this may
cause damage to the product.
!
NOTE
While charging: The LED is red.
When charging is complete: The LED is green.
When the battery is discharged: The Red LED blinks for 1 minute and turns off automatically.
The 3D glasses can still be used while charging via a USB device.
CAUTION
If you use a USB cable other the one (8-pin mini USB) supplied with the product, the product may be damaged.
This equipment shall be powered with USB 2.0 or higher.
Avoid twisting or dropping the 3D glasses as this may cause damage or break them.
Pull the nose pad in the direction shown by the
arrow as shown in the image. Be careful not
to twist or lift the nose pad as this can cause
damage.
Using 3D glasses may not be convenient for users wearing regular glasses. Adjusting the nose pad can
improve your viewing comfort.
USING 3D GLASSES
Button Operation
LED Indication
Power On
Press and hold the power button for 1 or 2
seconds.
The red LED blinks once.
Power Off
Press and hold down the Power button
(1 second ~2 second)
The red LED blinks three times.
Auto Off*
1
The device is automatically switched off if there
is no 3D signal for more than one minute.
The red LED blinks three times.
Battery(Lithium polymer)
discharge
If the battery is discharged, the red LED blinks
for 1 minute and turns off automatically.
* When charging is completed, the LED is lit green.
How to re-connect the
glasses
Press the power button for over eight seconds.
Release the button when the green LED light
turns on. Then, you will see the green light blink
three times before the device is switched off.
If you switch the power on again, the glasses
will be connected to the TV with the strongest
signal.
The Auto Off function automatically switches the power off when the glasses loose the signal from the TV.
This may occur when the distance or angle between the device and the TV are out of range; when there is a barrier between the two
devices; or when the device is switched from 3D to 2D mode.
!
NOTE
Follow the instructions in reverse order to put the nose pad back.
The nose pad can be adjusted even if you don’t wear glasses.
How to adjust the nose pad