LG DLG2525S Owners Manual - Page 9

Please, Aware, Failure, Exhaust, Dryer, Correctly, Dryer's, Warranty. - gas dryer

Get LG DLG2525S PDF manuals and user guides View all LG DLG2525S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

In addition to the following warnings, please refer to manual section on Exhaust Requirements and Maintenance. IMPORTANT." To reduce the risk of fire, combustion, and gas accumulation, the dryer must be vented to the outdoors. Please follow the instructions (and all others in this manual) very carefully. • ALTERNATE EXHAUST DIRECTIONS ] • Remove a screw and exhaust duct. 2- ]. Detach and remove a knockout at the button, left or right side as desired. (Right Side Vent not available on Gas dryer) (1-3, ('_), (5) the order of work. PORTION i "A" I • Do not use thin plastic or foil ducting. • Use 4" (10.2 cm) diameter rigid or flexible metal duct (note: venting materials are not supplied with the dryer, and you should obtain the venting materials necessary for proper installation) • Position the dryer where the exhaust duct is shorter as possible • Clean old ducts beJbre installing this dryer • The male end of each section of exhaust duct must point away from the dryer • Use fewer elbow joints as possible • Use duct tape on all duct joints • Insulate ductwork that runs through unheated areas in order to reduce condensation and lint build-up on pipe walls; and • PLEASE BE AWARE THAT FAILURE EXHAUST THE DRYER CORRECTLY VOID THE DRYER'S WARRANTY. TO WILL WARNING! • Use a heavy metal vent. • Do not use a plastic vent. • Do not use a metal foil vent. • Failure to follow these instructions can result in death or fire. • Clean old ducts before installing this dryer 2-2. Reconnect the another duct[11 in(28cm)] to the blower housing, and attach the duct to the base. (Duct is a SVC part) f \ 3-1. Pre-assemble 4" elbow with 4" duct. Wrap duct tape around joint. DUCT TAPE 3-2. Insert elbow duct assembly first through the side opening and connect the elbow to the internal duct. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
In addition
to the following
warnings,
please
refer
to manual
section
on Exhaust
Requirements
and
Maintenance.
IMPORTANT."
To reduce
the risk of
fire,
combustion,
and gas
accumulation,
the dryer
must
be vented
to the outdoors.
Please
follow
the
instructions
(and
all others
in this
manual)
very
carefully.
• Do not use thin
plastic
or foil
ducting.
• Use 4" (10.2
cm)
diameter
rigid
or flexible
metal
duct
(note:
venting
materials
are not supplied
with
the dryer,
and you
should
obtain
the
venting
materials
necessary
for proper
installation)
• Position
the
dryer
where
the exhaust
duct
is
shorter
as possible
•
Clean
old ducts
beJbre
installing
this
dryer
• The male
end of each
section
of exhaust
duct
must
point
away
from
the dryer
• Use fewer
elbow
joints
as
possible
• Use duct
tape
on
all
duct joints
• Insulate
ductwork
that runs
through
unheated
areas
in order
to reduce
condensation
and
lint
build-up
on pipe
walls;
and
•
PLEASE
BE
AWARE
THAT
FAILURE
TO
EXHAUST
THE
DRYER
CORRECTLY
WILL
VOID
THE
DRYER'S
WARRANTY.
WARNING!
•
Use a heavy
metal
vent.
• Do not use a plastic
vent.
• Do not use a metal
foil vent.
• Failure
to follow
these
instructions
can
result
in death
or fire.
• Clean
old ducts
before
installing
this dryer
•
ALTERNATE
EXHAUST
DIRECTIONS
]
•
Remove
a screw
and exhaust
duct.
2- ].
Detach
and remove
a knockout
at the
button,
left or right side as desired.
(Right
Side Vent not available
on Gas dryer)
(1-3, ('_),
(5)
the order of work.
i
PORTION
"A"
I
2-2.
f
\
Reconnect
the another
duct[11
in(28cm)]
to the blower
housing,
and attach
the
duct to the base.
(Duct
is a SVC
part)
3-1.
Pre-assemble
4" elbow with 4" duct.
Wrap
duct tape around
joint.
DUCT
TAPE
3-2.
Insert elbow duct assembly
first through
the
side
opening
and connect
the
elbow
to the
internal
duct.
9