LG DLG5932S Owners Manual - Page 14

hooked ends together.

Page 14 highlights

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw. % 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. t_ 1. Remove _nter terminal block screw. 2. Remove appliance ground wire (green) from external ground connector screw. Fasten it under _nter, silver colored terminal block screw. 3. Connect ground wire (green or bare) of power supply E cable to external ground conductor screw. Tighten screw. 4 I 3_ 2 I, 3-wire receptacle (NEMA type 10-30R) 2. 3-wire plug 3. Neutral prong 4. Spade terminals with up turned ends 5, 3/4 in. (1.9 cm) UL approved strain retie/ 6. Ring terminals 7. Neutral (white or center wire) Loosen or remove center terminal biock screw. Connect neutral wire (white or center wire) of power supply cord to the center, silver colored terminal screw of the terminal block. Tighten screw. 1, External ground connector 2 Green or bare copper wire of power supply cord 3. 3/4 in. (1.9 cm) UL qisted strain relief 4. Center silver_lered terminal block screw 5, Neutral grounding wire (green) 6_ Neutral wire (white) 4. Place the hooked end of the neutral wire (white wire) of power supply cable under the center screw of terminal block (hook facing fighO. Squeeze hooked end together. Tighten screw. 5. Place the hooked ends of the other power suppJy cable wires under the outer terminaJ bJock screws (hooks facing right). Squeeze hooked ends together. Tighten screws. 3 I, External ground connecter 2. Neutral grounding wire (green) 3. Center silver-colored terminal block screw 4. Neutral wire (white or center wire) 5. 3/4 in. (1.9 cm) UL-listed strain relief 3. Connect the other wires to outer terminal block screws. Tighten screws. 4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. Tighten strain relief screws. 7. Insert tab of terminal block cover into slot of dryer rear panel Secure cover with hold-down screw. I#

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

t_
E
I
When connecting
to the terminal block, place the hooked
end of the wire under the screw of the terminal
block (hook
facing right), squeeze
hooked end together and tighten
screw.
%
1. Remove _nter
terminal
block screw.
2. Remove appliance
ground wire (green) from external
ground connector
screw. Fasten it under _nter,
silver
colored terminal block screw.
3. Connect ground wire (green or bare) of power supply
cable to external ground conductor
screw. Tighten
screw.
4
3_
2
1, External ground
connector
2
Green or bare copper
wire
of power
supply cord
3. 3/4
in.
(1.9 cm) UL qisted strain
relief
4. Center silver_lered
terminal
block
screw
5,
Neutral
grounding
wire (green)
6_
Neutral
wire
(white)
4. Place the hooked end of the neutral wire (white wire)
of power supply cable under the center screw of
terminal block (hook facing fighO. Squeeze
hooked
end together. Tighten screw.
5. Place the hooked ends of the other power suppJy
cable wires under the outer terminaJ bJock screws
(hooks facing right). Squeeze
hooked ends together.
Tighten screws.
6. Tighten strain relief screws.
7. Insert tab of terminal block cover into slot of dryer
rear
panel
Secure cover with hold-down screw.
3-wire connection:
Power supply cord
Use
where
local
codes
permit
connecting
cabinet-ground
conductor
to neutral
wire.
I, 3-wire receptacle
(NEMA type
10-30R)
2. 3-wire plug
3. Neutral
prong
4. Spade
terminals
with up turned
ends
5, 3/4 in. (1.9 cm) UL approved
strain retie/
6. Ring terminals
7. Neutral
(white or center
wire)
Loosen or remove center terminal biock screw.
Connect neutral wire (white or center wire) of
power supply
cord to the center, silver colored
terminal screw of the terminal block. Tighten
screw.
3
I, External
ground
connecter
2. Neutral
grounding
wire (green)
3. Center
silver-colored
terminal
block
screw
4. Neutral
wire (white or center wire)
5. 3/4 in. (1.9 cm) UL-listed
strain relief
3. Connect the other wires to outer terminal block
screws. Tighten
screws.
4. Tighten strain relief screws.
5. Insert tab of terminal
block cover into slot of
dryer rear panel. Secure cover with hold-down
screw.
I
#