LG DLGX3701W Specification - Page 2

IMPORTANT HOME APPLIANCES LG COOKING DLEX3700_/DLGX3701_ 7.4 cu. ft. Front Load Dryer QUICK INSTALL & CLEARANCES For full installation directions/clearances please refer to the corresponding User Manual and Installation Guide. DIMENSIONS A Width B Height C Depth D Depth with Door Open Carton (WxHxD) ENERGY / POWER SOURCE Ratings Electrical Requirements Type BTU Rating 27" 38 11/16" 30" 51" 29 19/32" x 43 3/8" x 31 3/8" Yes CSA Listed 120V, 15 Amps (Gas) / 240V 30 Amps (Electric) Gas (DLGX3701_) / Electric (DLEX3700_) 10,000 Feet CONNECTING THE GAS SUPPLY • or the gas supplier. • • A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. • natural gas when shipped from the factory. Make sure that the dryer is equipped with the correct burner nozzle for the type of gas being used (natural 3/8" NPT gas Connection Stainless Steel Flexible Connector 1/8" NPT Pipe Plug Gas Supply Shutoff Valve gas or propane gas). • If necessary, the correct nozzle (for the LP nozzle kit, order part number be noted on the dryer. • All connections must be in accordance with local codes and regulations. Gas dryers MUST exhaust to the outdoors. CONNECTING ELECTRIC DRYERS • A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996. • A 3-wire connection is NOT permitted on new construction after January 1, 1996. • A UL-listed strain relief is required. • Use a 30-amp, 240-volt, 4-wire, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends. DIMENSIONS AND CLEARANCES 14" max.* 18" min. B C D 5"** 1" A 1" * Required spacing ** For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed. VENTING / DUCTWORK NOTE: Follow the guidelines below to maximize Correct Venting drying performance and reduce lint buildup and are NOT included and must be purchased separately. • Use 4-inch (10.2 cm) diameter rigid, semi-rigid or • The exhaust duct run should be as short as possible. • Use as few elbow joints as possible. • The male end of each section of exhaust duct must point away from the dryer. Incorrect Venting • Use duct tape on all duct joints. • Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces. • Incorrect or inadequate exhaust systems are not covered by the dryer warranty. Dryer failures or service required because of such exhaust systems will not be covered by the dryer warranty. • Ductwork is not provided with the dryer. You should obtain the necessary ductwork locally. The vent hood should have hinged dampers to prevent backdraft when the dryer is not in use. • metal duct must not exceed 8 ft. (2.4 m). • Deduct 6 ft. (1.8 m) for each additional elbow. Do not use more than four 90° elbows. Wall Cap Type Recommended Number of 90° Elbows 0 Maximum length of 4-inch diameter rigid metal duct 65 ft.(19.8 m) 1 55 ft.(16.8 m) a 2 47 ft.(14.3 m) a 3 a: 4" (10.2 cm) 4 Use only for short 0 run installations 1 2 b 3 b: 2.5" (6.35 cm) 4 36 ft.(11.0 m) 28 ft.(8.5 m) 55 ft.(16.8 m) 47 ft.(14.3 m) 41 ft.(12.5 m) 30 ft.(9.1 m) 22 ft.(6.7 m) © 2018 LG Electronics USA, Inc. All rights reserved. "LG Life's Good" is a registered trademark of LG Corp. All other product and brand names are trademarks or registered trademarks of their respective owners. Design, features and specifications are subject to change without notice. Non-metric weights and measurements are approximate. Some features may require Internet access. Content and services may vary by product and are subject to change without notice. 10/2/19