LG DLGX9001V Owners Manual - English Spanish - Page 18

Reversing the Door - parts for

Get LG DLGX9001V PDF manuals and user guides View all LG DLGX9001V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

18 INSTALLATION Reversing the Door WWARNING THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure to follow the instructions below can result in damage to the dryer, property damage or injury to persons. t5PBWPJEEBNBHFUPUIFESZFSPSUIFEPPS TVQQPSU UIFEPPSXJUIBTUPPMPSCPYUIBUGJUTVOEFSUIF EPPS PSIBWFBOBTTJTUBOUTVQQPSUUIFXFJHIUPG the door. t"MXBZTSFWFSTFUIFEPPS#&'03&TUBDLJOHUIF ESZFSPOUPQPGUIFXBTIFS t"WPJEESPQQJOHUIFEPPSUPBWPJEEBNBHFUPUIF EPPSPSUIFGMPPS 5PPMT/FFEFE flat blade screwdriver, Phillips screwdriver #FGPSF4UBSUJOH 1. Unplug the machine or turn off the power supply at the main circuit before reversing the door. Open the dryer door. 3FWFSTJOHUIF%PPST)JOHFBOE4USJLF 1. Remove the four screws on the right door frame (handle and strike), lift it off, and set the parts aside. (The two center strike screws are longer.) 2. Remove the four screws on the left door frame (hinge assembly). 3. Carefully lift out the hinge assembly, revealing the wire harness connector at the top of the hinge. Depress the side lock tab to disconnect the wire harness connector. 4. Rotate the hinge assembly 180 degrees and connect the wire harness to the connector in the bottom right side of the door. 5. Install the hinge assembly in the recess on the right side of the door, tucking the wire harness in the corner to make room. Insert and tighten the four screws. 6. Rotate the handle removed in step one 180 degrees and install it on the left side of the door using the two shorter screws. Use the longer screws to mount the door strike in the center. WWARNING #FTVSFUPTVQQPSUUIFXFJHIUPGUIFEPPSCFGPSF removing the hinge screws. 3FNPWJOHUIF%PPS 1. While supporting the door, remove the four hinge screws. 2. Carefully pull the door away from the cabinet to reveal the wire harness behind the hinge at the top. Depress the side lock tab to disconnect the wire harness connector. The twist tie and cap should prevent the wire harness from pulling back into the cabinet. 3. Remove the door from the cabinet cover. Set the door face down on a protected work surface. Cap R Frame L Frame R

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
18
flat blade screwdriver, Phillips screwdriver
1.
Unplug the machine or turn off the power supply at
the main circuit before reversing the door. Open the
dryer door.
WARNING
removing the hinge screws.
1.
While supporting the door, remove the four hinge
screws.
2.
Carefully pull the door away from the cabinet to reveal
the wire harness behind the hinge at the top. Depress
the side lock tab to disconnect the wire harness
connector. The twist tie and cap should prevent the
wire harness from pulling back into the cabinet.
3.
Remove the door from the cabinet cover. Set the door
face down on a protected work surface.
Cap R
1.
Remove the four screws on the right door frame
(handle and strike), lift it off, and set the parts aside.
(The two center strike screws are longer.)
2.
Remove the four screws on the left door frame (hinge
assembly).
3.
Carefully lift out the hinge assembly, revealing the
wire harness connector at the top of the hinge.
Depress the side lock tab to disconnect the wire
harness connector.
4.
Rotate the hinge assembly 180 degrees and connect
the wire harness to the connector in the bottom right
side of the door.
5.
Install the hinge assembly in the recess on the right
side of the door, tucking the wire harness in the corner
to make room. Insert and tighten the four screws.
6.
Rotate the handle removed in step one 180 degrees
and install it on the left side of the door using the two
shorter screws. Use the longer screws to mount the
door strike in the center.
Reversing the Door
WARNING
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure
to follow the instructions below can result in damage
to the dryer, property damage or injury to persons.
the door.
INSTALLATION
Frame L
Frame R