LG LRTN22324TT Owners Manual - Page 11

Closing, Alignment

Get LG LRTN22324TT PDF manuals and user guides View all LG LRTN22324TT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

3. Attaching Refrigerator Door • Attach the base grille (1). • Remove screw (2) from left side to right side. • Attach the door (3) to the bottom hinge pin. • Attach the middle hinge (4) on the opposite side with the 3 screws (5). 4. Attaching Freezer Door ° Place the door (8) onto the middle hinge pin (7). - Attach the top hinge (10) with 3 screws. • Reinstall top hinge cover (11). DOOR CLOSING AND ALIGNMENT Door Closing Your refrigerator has two front leveling screws--one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the Refrigerator's tilt using the instructions below: 1. Plug refrigerator power cord into a 3-prong grounded outlet. Move the refrigerator into its final position. 2. Remove the base grille by pulling it straight out. The two leveling screws are located at the bottom of the refrigerator on either side. . Insert a flat screwdriver in slots to adjust the leveling screws.Turn the leveling screw clockwise to raise that side of the refrigerator or counterclockwise to lower it. It may take several turns of the leveling screw to adjust the tilt of the refrigerator. NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws. This makes it easier to adjust the screws. 5. After Completing the Job - Make sure that the four corners of the door gasket are not folded over. To ensure a good seal, apply a small amount of silicon grease on the corner gaskets. 4. Open both doors again and check to make sure that they close easily. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws clockwise. It may take several more turns, and you should turn both leveling screws the same amount. 5. Replace the base grille. Door Alignment If the space between your doors is uneven, follow the instructions below to align the doors: 1. Pry off the top hinge cover. 2. Loosen the top hinge screws using a 10mm socket or wrench. . Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws. 4. Replace the top hinge cover. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
3. Attaching
Refrigerator
Door
• Attach the base grille (1).
• Remove
screw (2) from left side to right side.
• Attach the door (3) to the bottom hinge pin.
• Attach the middle hinge (4) on the opposite
side with the
3 screws (5).
4. Attaching
Freezer
Door
°
Place the door (8) onto the middle
hinge pin (7).
-
Attach the top hinge (10) with 3 screws.
• Reinstall top hinge cover (11).
DOOR
CLOSING
AND
ALIGNMENT
Door Closing
Your refrigerator
has two front leveling screws--one
on
the right and one on the left. If your refrigerator
seems
unsteady or you want the doors to close easier, adjust the
Refrigerator's
tilt using the instructions
below:
1. Plug refrigerator
power cord into a 3-prong grounded
outlet. Move the refrigerator
into its final position.
2. Remove
the base grille by pulling it straight out.
The two leveling screws are located at the bottom of
the refrigerator
on either side.
.
Insert a flat screwdriver
in slots to adjust the leveling
screws.Turn
the leveling screw clockwise
to raise that
side of the refrigerator
or counterclockwise
to lower it.
It may take
several turns of the leveling screw to adjust
the tilt of the refrigerator.
NOTE:
Having someone
push against the top of the
refrigerator
takes some weight
off the leveling screws.
This makes it easier to adjust the screws.
4. Open both doors again and check to make sure that
they close easily. If not, tilt the refrigerator
slightly more
to the rear by turning both leveling screws clockwise.
It
may take several more turns, and you should turn both
leveling screws the same amount.
5. Replace
the base grille.
5. After
Completing
the Job
- Make sure that the four corners of the door gasket are
not folded over. To ensure a good seal, apply a small
amount of silicon grease on the corner gaskets.
Door Alignment
If the space between your doors is uneven, follow the
instructions
below to align the doors:
1. Pry off the top hinge cover.
2. Loosen the top hinge screws
using a 10mm socket
or wrench.
.
Have someone
hold the door in place or put a
spacer between
the doors while you tighten the
top hinge screws.
4.
Replace
the top hinge cover.
11