LG LT1430CR Owners Manual - Page 12

Installation INSTALLATION We strongly recommend the removal of the old wall sleeve and the installation of a new LGE Wall Sleeve. If you decide to keep the existing wall sleeve, you have to redirect the louvers at the back of the wall sleeve illustration. The use of pliers is recommended. If you DO NOT redirect, you run the risk of poor performance or product failure. This is not covered under the terms of the LGE warranty. • Pick a location which will allow the conditioned air to blow into the area you want. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed. ITEMS IN INSTALLATION HARDWARE You may not need all parts in the kit. Discard unused parts ITEM (inches) Qty. Plastic grille 263/4 x 161/2 1 Vertical insulation strip 159/16 x 13/8 x 13/8 1 Around Insulation Strips 671/8 x 13/8 x 25/32 1 5927/32 x 13/8 x 13/8 1 Horizontal Insulation Strip 237/32 x 13/8 x 13/16 1 Support Block 13/4 x 13/8 x 45/16 2 Baffle 14 x 41/2 x 1/8 1 Shim 1113/16 x 1 x 3/4 2 Trim Frame 2 Washer Screw 4 Nuts(Plastic) 4 Grille Rear 1 HOW TO INSTALL 1 Identify the existing wall sleeve before installing the unit from the listed below. Brand White-Westinghouse Frigidaire Carrier (52F series) General Electric /Hotpoint Whirlpool Fedders/Emerson LGE Emerson/Fedders Carrier (51S Series) Friedrich Wall Sleeve Dimensions (inches) Width Height Depth 25-1/2 15-1/4 16, 17-1/2 or 22 26 15-5/8 16-7/8 25-7/8 27 25-7/8 26-3/4 25-3/4 27 16-1/2 17-1/8 or 23 16-3/4 16-3/4 or 19-3/4 15-17/32 16-23/32 15-3/4 15 16-7/8 18-5/8 16-3/4 16-3/4 NOTICE All wall sleeves used to mount the new Air Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve, or rear flange that serves as a stop for the Air Conditioner. 2 Remove old air conditioner from existing wall sleeve. 3 Clean the interior of an existing sleeve. (Do not disturb seals.) 4 Wall sleeve must be securely fastened in wall before installing the air conditioner. Use the nails or screws through sleeve into wall, if needed. Repaint sleeve if needed. 5 Prepare the wall sleeve for installation of the unit. If you plan to use your existing wall sleeve, and it is not LGE, use procedure B or C below. Procedure A B Brand LGE White-Westinghouse Frigidaire Carrier (52F series) General Electric /Hotpoint Whirlpool Carrier (51S series) Fedders/Emerson C Emerson/Fedders Friedrich Depth(inches) 16-23/32 16, 17-1/2 or 22 16-7/8 17-1/8 or 23 18-5/8 16-3/4 or 19-3/4 15 16-3/4 6 Install new unit into wall sleeve. When installation is completed, replacement unit MUST have a rearward slope as shown. To achieve 1/4" slope, remove the backing from the 11-13/16" shim strips and attach them as shown below in Fig. 3. Place the higher portion of shim to the front of the rib on base of wall sleeve. 1" high 3/4" High UNIT Wall Sleeve Shim FRONT 1/4" 6" 6" SHIM PLACEMENT UNIT INSTALLATION FIG. 3 12 Room Air Conditioner