LG WM0001HTMA Owner's Manual - Page 11

Unpacking And Removing Shipping Bolts, Warning

Get LG WM0001HTMA PDF manuals and user guides View all LG WM0001HTMA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

INSTALLATION INSTRUCTIONS UNPACKING AND REMOVING SHIPPING BOLTS When removing the washer from the carton base, be sure to remove the foam tub support in the middle of the carton base. If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. Do NOT lay the washer on its front or back. IMPORTANT: To prevent internal damage during transport, the washer is equipped with 4 shipping bolts and plastic retainers. These bolts and retainers MUST be removed before operating the washer. • Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place. Foam Tub Support Carton Base Shipping Bolts Retainer Hole Cap 1 Starting with the bottom 2 shipping bolts, use the included wrench to remove the 4 shipping bolts by turning them counterclockwise. w WARNING To reduce the risk of injury to persons when using this cleaner, follow basic To reduce the risk of fire when using and install this appliance follow basic precautions, including the following : • Do not install nearby heat item. Such as stove, cooking oven. Failure to do so can cause deform, smoke and fire. • Do not place candle and cigarettes on top of the product. Failure to do so can cause deform, smoke and fire. • Remove all protective vinyl film from the product. Failure to do so can cause deform, smoke and fire. Removing the Protective Film The top, sides, and front of the washer are covered with a protective vinyl film. This film is to protect the finish during shipping, and should be removed before use. 2 Remove the retainers by turning them slightly while pulling. Rotate and press the hole caps into the shipping bolt holes. NOTE: Save the bolts and retainers for future use. To prevent damage to internal components, the shipping bolts and retainers must be installed when transporting the washer. Once the protective film has been removed, transfer the Service Call Number label from the top film to an easy to find location on the side of the washer. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
INSTALLATION INSTRUCTIONS
When removing the washer from the carton base, be
sure to remove the foam tub support in the middle of the
carton base.
If you must lay the washer down to remove the base
packaging materials, always lay it carefully on its side. Do
NOT lay the washer on its front or back.
IMPORTANT:
To prevent internal damage during transport,
the washer is equipped with 4 shipping bolts and plastic
retainers. These bolts and retainers
MUST
be removed
before operating the washer.
• Failure to remove shipping bolts and retainers may cause
severe vibration and noise, which can lead to permanent
damage to the washer. The cord is secured to the back of
the washer with a shipping bolt to help prevent operation
with shipping bolts in place.
Remove the retainers by turning them slightly
while pulling. Rotate and press the hole caps
into the shipping bolt holes.
Starting with the bottom 2 shipping bolts,
use the included wrench to remove the
4 shipping bolts by turning them
counterclockwise.
1
Shipping
Bolts
2
NOTE:
Save the bolts and retainers for
future use. To prevent damage to internal
components, the shipping bolts and
retainers must be installed when
transporting the washer.
Retainer
Hole Cap
Carton Base
Foam Tub
Support
UNPACKING AND REMOVING SHIPPING BOLTS
Removing the Protective Film
The top, sides, and front of the washer are covered
with a protective vinyl film. This film is to protect
the finish during shipping, and should be removed
before use.
Once the protective film has been removed, transfer
the Service Call Number label from the top film to an
easy to find location on the side of the washer.
w
WARNING
To reduce the risk of injury to persons when using this cleaner,
follow basic To reduce the risk of fire when using and install this
appliance
follow basic precautions, including the following :
• Do not install nearby heat item. Such as stove,
cooking oven.
Failure
to do so can cause deform, smoke and fire.
• Do not place candle and cigarettes on top of the product.
Failure to do so can cause deform, smoke and fire.
• Remove all protective vinyl film from the product.
Failure
to do so can cause deform, smoke and fire.
11