LG WT901CF Additional Link - Owner s Manual - Page 30

Checking Error Messages Continued

Get LG WT901CF PDF manuals and user guides View all LG WT901CF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

30 TROUBLESHOOTING CHECKING ERROR MESSAGES (CONTINUED) Problem Possible Cause Water in the washer drains slowly Drain hose is kinked, pinched, or or not at all, or the display shows: clogged The display shows: Drain discharge is more than 96 inches above bottom of washer. If the uE rebalance (see above) is not successful, this error will be displayed. The load is too small. Heavy articles are mixed with lighter items. The display shows : The load is out of balance. Water level is too high due to a faulty water valve. Solutions Make sure the drain hose is free of clogs, kinks, etc., and is not pinched behind or under the washer. Adjust or repair drain. Maximum drain height is 96 inches (8 ft.) The automatic attempt to rebalance the load was not successful. The cycle has been paused to allow the load to be manually adjusted. Small loads may need additional items to be added to allow the washer to balance the loads. The load may have heavy items loaded with lighter items. Always try to wash articles of somewhat similar weight to allow the washer to evenly distribute the weight of the load for spinning. Manually redistribute the load if articles have become tangled preventing the automatic distribution from working properly. Close the water faucets, unplug the washer, and call for service. The display shows: The water level sensor is not working correctly. Close the water faucets, unplug the washer, and call for service. The display shows: The washer has detected an out of If the washer detects a load that is too far balance load. out of balance to spin, it will display this code while it is attempting to rebalance the load. The washer will add water and try to redistribute the load automatically. This display is for your information only, and no action is required.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
30
TROUBLESHOOTING
CHECKING ERROR MESSAGES (CONTINUED)
Problem
Possible Cause
Solutions
Water in the washer drains slowly
or not at all, or the display shows:
Drain hose is kinked, pinched, or
clogged
Drain discharge is more than 96
inches above bottom of washer.
Make sure the drain hose is free of clogs,
kinks, etc., and is not pinched behind or
under the washer.
Adjust or repair drain. Maximum drain height
is 96 inches (8 ft.)
The display shows:
If the uE rebalance (see above) is
not successful, this error will be
displayed.
The automatic attempt to rebalance the load
was not successful. The cycle has been
paused to allow the load to be manually
adjusted.
The load is too small.
Small loads may need additional items to be
added to allow the washer to balance the
loads.
Heavy articles are mixed with
lighter items.
The load may have heavy items loaded with
lighter items. Always try to wash articles of
somewhat similar weight to allow the washer
to evenly distribute the weight of the load for
spinning.
The load is out of balance.
Manually redistribute the load if articles have
become tangled preventing the automatic
distribution from working properly.
The display shows
:
Water level is too high due to a
faulty water valve.
Close the water faucets, unplug the washer,
and call for service.
The display shows:
The water level sensor is not
working correctly.
Close the water faucets, unplug the washer,
and call for service.
The display shows:
The washer has detected an out of
balance load.
If the washer detects a load that is too far
out of balance to spin, it will display this code
while it is attempting to rebalance the load. The
washer will add water and try to redistribute
the load automatically. This display is for your
information only, and no action is required.