Lacie 12big Rack Network User Manual - Page 53

LaCie 12big Rack Network User Manual Fig. 38 - Rail Kit Installation Drawing PART NO. 82864-01 A 1 OF 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 REV DATE SIG ECN No. REV DATE SIG ECN No. REV SHEET NO. A IF IN DOUBT ASK 01-A 18/08/2006 NH 25440 A REMOVE THIS NUT B IF INSTALLING INTO TAPPED HOLE RACK B C C FIGURE 1 CLAMPING SCREWS 12 6 D D 5 1 E TAPPED HOLE RACK FRONT RACK POST F G H 4 2 SQUARE HOLE RACK FRONT RACK POST USE SAME SCREWS AND WASHERS ON FRONT AND REAR POSTS I ASSEMBLY INSTRUCTIONS 1. PERFORM THIS STEP ONLY IF INSTALLING INTO A TAPPED HOLE RACK:REMOVE THE NUT SHOWN IN FIGURE 1 USING THE SPANNER SUPPLIED. 2. ASSEMBLE (2x) ITEMS 6 (NOT HANDED) TO RIGHT AND LEFT SIDES OF RACK. FIT THE LOCATION PIN AT THE REAR END OF RAIL ITEM 6 INTO THE REAR RACK POST. J EXTEND THE RAIL TO FIT BETWEEN THE FRONT AND REAR RACK POSTS, ATTACH TO BOTH THE FRONT AND REAR OF RACK USING SCREW & WASHER COMBINATION: ROUND HOLE - ITEMS 3 AND 4, SQUARE HOLE - ITEMS 2 AND 4, TAPPED HOLE - ITEMS 1 AND 5 SCREWS SHOULD BE LEFT LOOSE ENOUGH TO ALLOW RAIL SIDEWAYS MOVEMENT ON ITS SLOTS. TIGHTEN (2x) CLAMPING SCREWS 3. MOUNTING CHASSIS INTO RACK. K LIFT CHASSIS AND ALIGN WITH RACK RAILS, CAREFULLY INSERT CHASSIS SLIDES INTO RACK RAILS AND PUSH FULLY HOME. TIGHTEN REAR SCREWS, WITHDRAW CHASSIS UNTIL IT REACHES HARD STOPS (APPROX 400mm). TIGHTEN FRONT SCREWS. RETURN CHASSIS TO FULLY HOME POSITION AND ATTACH TO RACK USING CAPTIVE FASTENERS ON FRONT FLANGES. 4. CHASSIS REMOVAL. THE CHASSIS RAILS HAVE FEATURES TO RESTRICT IT'S WITHDRAWAL WHILST STILL ALLOWING ACCESS TO THE FAN TRAY. TO REMOVE IT COMPLETELY, PULL THE CHASSIS OUT UNTIL IT REACHES ITS STOPS, THEN THE BLUE LATCHES MUST BE ROTATED (RIGHT HAND UP, LEFT HAND DOWN), THE CHASSIS CAN THEN CONTINUE TO BE FULLY WITHDRAWN. L 1 2 3 4 5 6 7 E REAR RACK POST LEFT HAND ASSEMBLY SHOWN F RAIL KIT CAN BE ADJUSTED TO FIT RACKS OF SIZES (BETWEEN INTERNAL FACES): MINIMUM: 685mm, MAXIMUM: 889mm G H 4 3 ROUND HOLE RACK FRONT RACK POST I SUPPLY COMPONENTS IN BAGS MARKED AS SHOWN. Parts List ITEM QT PART NUMBER DESCRIPTION BAG 1 8 15275-01 2 8 56178-02 M5 SPRING WASHER ATX RACK SLIDE WASHER SQUARE HOLE TAPPED HOLE RACK SQUARE HOLE RACK J 3 8 57599-02 ATX RACK SLIDE WASHER ROUND HOLE ROUND HOLE RACK 4 8 64376-01 M5 x 12 CSK PHILLIPS PATCHLOCK 5 8 64377-01 SCREW 10-32 UNF SPECIAL PHILLIPS TAPPED HOLE RACK 6 2 71997-02 ATX RACK BRACKET ASSEMBLY UNIVERSAL 7 1 72046-01 10mm SPANNER TAPPED HOLE RACK 8 1 82864-01 ATX REDUCED RAIL KIT REFERENCE DRAWING K THIS DRAWING THIS PART/ASSEMBLY SHALL BE MANUFACTURED FROM RoHS COMPLIANT MATERIALS/COMPONENTS, IN ACCORDANCE WITH EU DIRECTIVE 2002/95/EC. MATERIAL TOLERANCES UNLESS STATED 0 DECIMAL PLACE : ± 0.5 DRAWN N Hunt CHECKED DATE 18/08/2006 DATE 1 DECIMAL PLACE : ± 0.2 2 DECIMAL PLACES : ± 0.1 APPROVED DATE FINISH SURFACE TEXTURE ANGLES : ± 0.5° RADII UNLESS STATED : SEE PARTS MAX EDGE BREAKS : DIMENSIONS mm SCALE 1:1 8 9 10 11 12 13 PART NO. 82864-01 REV SHEET NO. A 1 OF 1 SIZE TITLE 0 ATX REDUCED RAIL KIT L 14 15 16 Rack Kit Reference Drawing page 53