Home » Lacie Manuals » Hard Drives » Lacie 2big » Manual Viewer

Lacie 2big User Manual - Page 20

To Insert a Disk - replace drive

Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

5. Grasp the drive tray handle and carefully extract the drive. Important info: LaCie highly recommends replacing the disk that has been removed as soon as possible. To Insert A Disk 1. Confirm that the 2big Thunderbolt Series enclosure is off. 2. Remove the failed disk according to the instructions above. Please make certain that you are properly grounded to avoid electrostatic discharge. 3. Remove the screws from the drive tray to replace the failed drive with the disk that you received from LaCie. 4. Fasten the screws back on the drive tray. 5. Carefully insert the drive tray into the empty disk bay. When the drive tray is almost flush, you will feel a bit of resistance. Press the drive tray handle firmly until the drive snaps into place and it is in line with the back pane of the 2big Thunderbolt Series. 6. Use the 2-in-1 tool to fasten the drive lock. The drive is locked when the line is in a horizontal position. LaCie 20

Section	Page
Thunderbolt Series User Manual	1
Introduction	2
Box Content	2
Minimum System Requirements	2
Views of the Drive	3
Front View	3
Rear View	5
Hard Disk Heat Management	7
Heat Dissipation Design	7
Position and Stacking	7
Receiving Power/LED Power Button	10
Receiving Power	10
Multi-functional LED/Power Button	10
LED States - 2big Thunderbolt Series	10
LED States - Little Big Disk Thunderbolt Series	10
Power Button	11
Thunderbolt Technology and Daisy Chain	12
Thunderbolt Technology	12
Daisy Chain	13
Getting Connected	14
Connect the Interface Cable	14
Unmounting the Thunderbolt Series Volume	17
Unmounting Your Drive	18
Replacing a Disk (2big)	19
To Remove a Disk	19
To Insert a Disk	20
Rebuilding a RAID Set	21
Formatting	22
Striped RAID Set (RAID 0)	22
Mirrored RAID Set (RAID 1)	22
Configuring a RAID Set	23
Getting Help	29
Troubleshooting Topics	30
Problem: I do not see my Thunderbolt Series disks.	30
Problem: I'm receiving file transfer error messages and Time Machine does not work.	31
Problem: The disk space does not seem right.	31
Problem: I have to rebuild the Mirrored RAID Set.	31
Precautions	32
Health and Safety Precautions	32
General Use Precautions	32
Warranty Information	34
LaCie Limited Warranty Policy	34
EXCLUSIONS AND LIMITATIONS	34
Service DOA	35
Advance Care Option	35
Customer Warning	36
Legal Information	37
Copyrights	37
Changes	37
Federal Communication Commission Interference Statement	37
WEEE	38
Manufacturer's Declaration for CE Certification	38
Trademarks	38
Canada Compliance Statement	38

Match case Limit results 1 per page

Grasp the drive tray handle and carefully extract the drive.

Important info:

LaCie highly recommends replacing the disk that has been removed as soon as possible.

To Insert A Disk

Confirm that the 2big Thunderbolt Series enclosure is off.

Remove the failed disk according to the instructions above. Please make certain that you are properly

grounded to avoid electrostatic discharge.

Remove the screws from the drive tray to replace the failed drive with the disk that you received from LaCie.

Fasten the screws back on the drive tray.

Carefully insert the drive tray into the empty disk bay. When the drive tray is almost flush, you will feel a bit

of resistance. Press the drive tray handle firmly until the drive snaps into place and it is in line with the back

pane of the 2big Thunderbolt Series.

Use the 2-in-1 tool to fasten the drive lock. The drive is locked when the line is in a horizontal position.

LaCie