Lantronix C4110-4848 CLI Reference Guide Rev B PDF 873.04 KB - Page 6

Managing Slide-In and Remote Modules via CLI Commands, Related Manuals

Get Lantronix C4110-4848 PDF manuals and user guides View all Lantronix C4110-4848 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Transition Networks ION x4110 CLI Reference Related Manuals A printed documentation card is shipped with each x4110 device. Context-sensitive Help screens, as well as cursor-over-help (COH) facilities are built into the Web interface. A substantial set of technical documents, white papers, case studies, etc. are available on the Transition Networks web site at https://www.transition.com. Note that this manual provides links to third part web sites for which Transition Networks is not responsible. Other ION system and related device manuals are listed below. • Product Documentation Postcard, 33504 • C4110 Install Guide, 33572 • S4110 Install Guide, 33573 • x4110 Web User Guide, 33574 • x4110 CLI Reference, 33575 (this manual) • Focal Point™ 3.0 Management Application User Guide, 33293 • ION Management Module (IONMM) User Guide, 33457 and Install Guide, 33420 • SFP manuals (product specific) • ION System NID User Guides (33432, 33457, 33472, 33493, 33494, 33495, 33496) • Release Notes (firmware version specific) Note: This manual may provide links to third part web sites for which Transition Networks is not responsible. Information in this document is subject to change without notice. All information was deemed accurate and complete at the time of publication. This manual documents the latest software/firmware version. While all screen examples may not display the latest version number, all of the descriptions and procedures reflect the latest software/firmware version, noted in the Revision History on page 2. Managing Slide-In and Remote Modules via CLI Commands Management of modules other than the IONMM can be accomplished by entering CLI commands through either the local USB serial interface or a remote Telnet session. CLI commands can operate on the device level or port level. This is indicated by the status of the command prompt's preamble. For example: AgentIII C1|S7|L1D> or just: C1|S1|L1D> This prompt indicates that any subsequent commands entered are for the module located in chassis 1/slot1. In order to enter a command for a different device or port in the ION system, you must change the location of the command prompt. The go command lets you change the hierarchical location of the command prompt. Before using the command, a familiarity with the hierarchy structure in the ION system is essential. 33575 Rev. B https://www.transition.com 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Transition Networks
ION x4110 CLI Reference
33575 Rev. B
6
Related Manuals
A printed documentation card is shipped with each x4110 device. Context-sensitive Help screens, as well
as cursor-over-help (COH) facilities are built into the Web interface. A substantial set of technical
documents, white papers, case studies, etc. are available on the Transition Networks web site at
. Note that this manual provides links to third part web sites for which Transition
Networks is not responsible.
Other
ION system and related device manuals are listed below.
•
Product Documentation Postcard, 33504
•
C4110 Install Guide, 33572
•
S4110 Install Guide, 33573
•
x4110 Web User Guide, 33574
•
x4110 CLI Reference, 33575 (this manual)
•
Focal Point
™
3.0 Management Application User Guide, 33293
•
ION Management Module (IONMM) User Guide, 33457 and Install Guide, 33420
•
SFP manuals (product specific)
•
ION System NID User Guides (33432, 33457, 33472, 33493, 33494, 33495, 33496)
•
Release Notes (firmware version specific)
Note
: This manual may provide links to third part web sites for which Transition Networks is not respon-
sible. Information in this document is subject to change without notice. All information was deemed accu-
rate and complete at the time of publication. This manual documents the latest software/firmware version.
While all screen examples may not display the latest version number, all of the descriptions and proce-
dures reflect the latest software/firmware version, noted in the
Revision History
on page
2
.
Managing Slide-In and Remote Modules via CLI Commands
Management of modules other than the IONMM can be accomplished by entering CLI commands
through either the local USB serial interface or a remote Telnet session. CLI commands can operate on
the device level or port level. This is indicated by the status of the command prompt’s preamble.
For example:
AgentIII C1|S7|L1D>
or just:
C1|S1|L1D>
This prompt indicates that any subsequent commands entered are for the module located in chassis
1/slot1. In order to enter a command for a different device or port in the ION system, you must change the
location of the command prompt. The
go
command lets you change the hierarchical location of the
command prompt. Before using the command, a familiarity with the hierarchy structure in the ION
system is essential.