Home » Lantronix Manuals » Electronics Accessories » Lantronix MSS4 » Manual Viewer

Lantronix MSS4 MSS Reference Manual - Page 36

Change Incoming

Get Lantronix MSS4 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Change Incoming Parameters Defaults Examples See Also Command Reference Server MSS4 only. period Enter a length of time in minutes (1 to 120) or seconds (5 to 60). For minutes, add an m after the number. For seconds, add an s after the number. 30 minutes Local> CHANGE INACTIVE TIMER 10m Change Inactive Logout, page 2-25. 2.23 Change Incoming CHANGE     SERVER INCOMING        TELNET   LAT BOTH    NONE   PASSWORD   NOPASSWORD   Permits or denies incoming Telnet, Rlogin, and LAT connections and enforces password protection. The Show Server command shows the status of incoming connection parameters. Restrictions Requires privileged user status. The MSSLite, MSS-VIA, and the MSS4 do not support LAT or the Both parameter. Parameters Server MSS4 only. Telnet Enables incoming Telnet connections. LAT Enables incoming LAT connections. Both Enables incoming Telnet and incoming LAT connections. Only valid on models with LAT support. None Disables all incoming connections. 2-26

Section	Page
Title	1
Contents	3
1: Introduction	7
1.1 What’s New	7
1.2 Command Syntax	7
1.3 Command Line Editing	8
1.4 Help	9
1.5 About This Manual	9
2: Command Reference	11
2.1 Backward	12
2.2 Change 80211	12
2.2.1 Change 80211 Enabled	12
2.2.2 Change 80211 Antenna	13
2.2.3 Change 80211 Channel	14
2.2.4 Change 80211 ESSID	14
2.2.5 Change 80211 Fragmentation	15
2.2.6 Change 80211 MAC Address	15
2.2.7 Change 80211 Network Mode	16
2.2.8 Change 80211 Power	17
2.2.9 Change 80211 Region	17
2.2.10 Change 80211 Reset	18
2.2.11 Change 80211 RTS	18
2.2.12 Change 80211 WEP	19
2.3 Change Access	20
2.4 Change Autobaud	21
2.5 Change Autostart	22
2.6 Change Backward Switch	24
2.7 Change Bootgateway	24
2.8 Change BOOTP	25
2.9 Change Break	25
2.10 Change Buffering	26
2.11 Change Charsize	26
2.12 Change Datasend	27
2.13 Change Dedicated	29
2.14 Change DHCP	31
2.15 Change Domain	31
2.16 Change DSRLogout	32
2.17 Change DTRWait	32
2.18 Change Flow Control	33
2.19 Change Forward Switch	34
2.20 Change Gateway	34
2.21 Change Inactive Logout	35
2.22 Change Inactive Timer	35
2.23 Change Incoming	36
2.24 Change IPAddress	37
2.25 Change IPSecurity	37
2.26 Change LAT CircTimer	38
2.27 Change LAT Groups	39
2.28 Change LAT Identification	39
2.29 Change Loadhost	39
2.30 Change Local Switch	40
2.31 Change Loginpass	41
2.32 Change Modem Control	41
2.33 Change Modem Emulation	42
2.34 Change Name	42
2.35 Change Nameserver	43
2.36 Change NetWare Encapsulation	43
2.37 Change NetWare Internal Network	44
2.38 Change NetWare Loadhost	44
2.39 Change NetWare Routing	45
2.40 Change Parity	45
2.41 Change Passflow	46
2.42 Change Password Incoming	47
2.43 Change Password Limit	47
2.44 Change Password Protect	48
2.45 Change Portname	48
2.46 Change Preferred	49
2.47 Change Privpass	50
2.48 Change RARP	50
2.49 Change Retransmit Limit	51
2.50 Change Rlogin	51
2.51 Change RS485	52
2.52 Change Secondary	53
2.53 Change Session Limit	53
2.54 Change Signal Check	53
2.55 Change Silentboot	54
2.56 Change SNMPSetComm	54
2.57 Change Software	55
2.58 Change Speed	55
2.59 Change Startup	56
2.60 Change Stopbits	57
2.61 Change Subnet Mask	57
2.62 Change TCPKeepalive	58
2.63 Change Telnetdest	58
2.64 Change Telnetpad	59
2.65 Change Termtype	59
2.66 Change Timeserver	60
2.67 Change Verify	61
2.68 Change WINS	61
2.69 Crypt Password	62
2.70 Disk	63
2.71 Delete IPSecurity	67
2.72 Disconnect	67
2.73 Finger	67
2.74 Forward	68
2.75 Help	68
2.76 Hostlist	68
2.77 Initialize	69
2.78 LAT	70
2.79 Logout Port	70
2.80 Netstat	71
2.81 Ping	71
2.82 Resume	71
2.83 Rlogin	72
2.84 RTC	72
2.85 Set Privileged	73
2.86 Show 80211	73
2.87 Show Hostlist	74
2.88 Show IPsecurity	74
2.89 Show NetWare	74
2.90 Show Nodes	74
2.91 Show Ports	75
2.92 Show RS485	75
2.93 Show Server	75
2.94 Show Services	76
2.95 Show Session	76
2.96 Show SNMP	77
2.97 Show Users	77
2.98 Show Version	77
2.99 Source	77
2.100 SPX	78
2.101 Telnet	78
2.102 Test	79
2.103 Zero	79
A: Contact Information	81
A.1 Problem Report Procedure	81
A.2 Full Contact Information	81
B: Environment Strings	83
B.1 Usage	83
B.1.1 Multiple Strings	83
B.2 Available Strings	83
B.2.1 Usage Examples	84
2.2.1.1 nnnn	84
2.2.1.2 +C and -C	84
2.2.1.3 +D and -D	84
2.2.1.4 +E and -E	84
2.2.1.5 OR	85
2.2.1.6 OS	85
2.2.1.7 +P and -P	85
2.2.1.8 R	85
2.2.1.9 T	85
2.2.1.10 U	85
2.2.1.11 Y	86
2.2.1.12 LD=port#	86
2.2.1.13 LN=node#	86
C: Show 802.11 Errors	87
C.1 Introduction	87
C.2 Error Bits	87
C.2.1 Leftmost Number	87
C.2.2 Rightmost Number	89