Lantronix Micro125 Micro125 - User Guide - Page 36

Serial Port Connection, To establish a Telnet connection, Start, press Enter within 5 seconds

Get Lantronix Micro125 PDF manuals and user guides View all Lantronix Micro125 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

6: Configuration via Telnet or Serial Port (Setup Mode) To establish a Telnet connection: 1. From the Windows Start menu, click Run and type the following command, where x.x.x.x is the IP address, and 9999 is the unit's fixed network configuration port number: Windows: telnet x.x.x.x 9999 UNIX: telnet x.x.x.x:9999 2. Click OK. The following information displays. Figure 6-1. MAC Address MAC address 00204AAE0412 Software version V6.8.0.4 (121207) M125 AES library version 1.8.2.1 Press Enter for Setup Mode 3. To enter Setup Mode, press Enter within 5 seconds. The configuration settings display, followed by the Change Setup menu. Figure 6-2. Setup Menu Options Change Setup: 0 Server 1 Channel 1 2 Channel 2 5 Expert 6 Security 7 Defaults 8 Exit without save 9 Save and exit Your choice? 4. Select an option on the menu by entering the number of the option in the Your choice ? field and pressing Enter. 5. To enter a value for a parameter, type the value and press Enter, or to confirm a current value, just press Enter. 6. When you are finished, save the new configuration (option 9). The unit reboots. Serial Port Connection To configure the unit through a serial connection: 1. Connect a console terminal or PC running a terminal emulation program to your unit's serial port. 2. Set the terminal emulator serial port settings to 9600 baud, 8 bits, no parity, 1 stop bit, no flow control. Note: The Micro125 always uses these serial port settings on boot-up. 3. Reset the Micro125 unit by cycling the unit's power (turning the power off and back on). Immediately upon resetting the device, enter three lowercase x characters (xxx). Micro125 User Guide 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
6: Configuration via Telnet or
Serial Port (Setup Mode)
To establish a Telnet connection:
1. From the Windows
Start
menu, click
Run
and type the following command, where x.x.x.x
is the IP address, and 9999 is the unit’s fixed network configuration port number:
Windows:
telnet x.x.x.x 9999
UNIX:
telnet x.x.x.x:9999
2. Click
OK
. The following information displays.
Figure 6-1. MAC Address
MAC address 00204AAE0412
Software version V6.8.0.4 (121207) M125
AES library version 1.8.2.1
Press Enter for Setup Mode
3.
To enter Setup Mode,
press Enter within 5 seconds
. The configuration settings display,
followed by the Change Setup menu.
Figure 6-2. Setup Menu Options
Change Setup:
0 Server
1 Channel 1
2 Channel 2
5 Expert
6 Security
7 Defaults
8 Exit without save
9 Save and exit
Your choice?
4.
Select an option on the menu by entering the number of the option in the
Your choice
?
field and pressing
Enter
.
5.
To enter a value for a parameter, type the value and press
Enter
, or to confirm a current
value, just press
Enter
.
6.
When you are finished, save the new configuration (option 9). The unit reboots.
Serial Port Connection
To configure the unit through a serial connection:
1.
Connect a console terminal or PC running a terminal emulation program to your unit's
serial port.
2.
Set the terminal emulator serial port settings to 9600 baud, 8 bits, no parity, 1 stop bit, no
flow control.
Note:
The Micro125 always uses these serial port settings on boot-up.
3.
Reset the Micro125 unit by cycling the unit's power (turning the power off and back on).
Immediately upon resetting the device, enter three lowercase
x
characters (
xxx
).
Micro125 User Guide
36