Home » Lantronix Manuals » Electronics Accessories » Lantronix PremierWave SE1000 » Manual Viewer

Lantronix PremierWave SE1000 PremierWave SE1000 - User Guide - Page 79

To Specify Clock Setting Method, Using Web Manager, Using the CLI, System Settings

View all Lantronix PremierWave SE1000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

12: Maintenance and Diagnostics Settings Time Zone Select the Time Zone of the device according to Coordinated Universal Time (UTC). Syslog and other applications may use UTC. The UTC offset form is HHMM (H=hour, M=minute). Device will make seasonal changes required for daylight savings time. To Specify Clock Setting Method Using Web Manager  To view thread information, click Clock in the menu. Using the CLI  To enter the command level: enable -> config -> clock Using the XML  Include in your file: System Settings The PremierWave SE1000 embedded system on module system settings allow for rebooting the device, restoring factory defaults, uploading new firmware and updating a system's short and long name. Note: Anytime you reboot the unit, this operation will take some time to complete. Please wait a minimum of 10-20 seconds after rebooting the unit before attempting to make any subsequent connections. Table 12-11 System Settings System Settings Description Reboot Device Reboots the device. Restore Factory Defaults Restores the device to the original factory settings. All configuration will be lost. The PremierWave unit automatically reboots upon setting back to the defaults. Upload New Firmware FTP to the PremierWave device. Write the new firmware file to firmware.rom on the PremierWave unit. The device automatically reboots upon the installation of new firmware. See the section, FTP Settings on page 52. Short Name Enter a short name for the system name. A maximum of 32 characters are allowed. Long Name Enter a long name for the system name. A maximum of 64 characters are allowed. PremierWave® SE1000 Embedded System on Module User Guide 79

Section	Page
PremierWave SE1000 Embedded System on Module User Guide	1
Intellectual Property	2
Warranty	2
Contacts	2
Disclaimer	2
Revision History	2
Table of Contents	3
List of Figures	12
List of Tables	13
1: Using This Guide	15
Purpose and Audience	15
Summary of Chapters	15
Additional Documentation	16
2: Introduction	17
Key Features	17
Applications	18
Protocol Support	18
Troubleshooting Capabilities	18
Configuration Methods	19
Addresses and Port Numbers	19
Hardware Address	19
IP Address	19
Port Numbers	20
Product Information Label	20
3: Device Discovery and Quick Setup	21
Accessing the PremierWave SE1000 Device Using UPnP	21
Accessing the PremierWave SE1000 Device Using DeviceInstaller	22
Device Detail Summary	22
4: Configuration Using Web Manager	24
Accessing Web Manager	24
Device Status Page	25
Web Manager Components	26
Web Manager pages have these sections:	26
Navigating Web Manager	27
5: Network Settings	29
Network 1 (Ethernet “eth0”) Interface Settings	29
To Configure Network 1 Interface Settings	30
Using Web Manager	30
Using the CLI	30
Using XML	30
To View Network 1 Interface Status	30
Using Web Manager	30
Network 1 (Ethernet “eth0”) Link Settings	31
To Configure Network 1 Link Settings	31
Using Web Manager	31
Using the CLI	31
Using XML	31
WAN MAC Address Filters	31
6: Line and Tunnel Settings	32
USB-CDC-ACM	32
Line Settings	33
To Configure Line Settings	35
Using Web Manager	35
Using the CLI	35
Using XML	35
To View Line Statistics	35
Using Web Manager	35
Using the CLI	35
Using XML	35
Tunnel Settings	35
Serial Settings	35
To Configure Tunnel Serial Settings	36
Using Web Manager	36
Using the CLI	36
Using XML	36
Packing Mode	36
To Configure Tunnel Packing Mode Settings	37
Using Web Manager	37
Using the CLI	37
Using XML	37
Accept Mode	37
To Configure Tunnel Accept Mode Settings	39
Using Web Manager	39
Using the CLI	39
Using XML	39
Connect Mode	40
To Configure Tunnel Connect Mode Settings	41
Using Web Manager	41
Using the CLI	41
Using XML	41
Disconnect Mode	41
To Configure Tunnel Disconnect Mode Settings	42
Using Web Manager	42
Using the CLI	42
Using XML	42
Modem Emulation	42
To Configure Tunnel Modem Emulation Settings	43
Using Web Manager	43
Using the CLI	43
Using XML	43
Statistics	44
To View Tunnel Statistics	44
Using Web Manager	44
Using the CLI	44
Using XML	44
7: Terminal and Host Settings	45
Terminal Settings	45
To Configure the Terminal Network Connection	46
Using Web Manager	46
Using the CLI	46
Using XML	46
To Configure the Terminal Line Connection	46
Using Web Manager	46
Using the CLI	46
Using XML	46
Host Configuration	46
To Configure Host Settings	47
Using Web Manager	47
Using the CLI	47
Using XML	47
8: Configurable Pin Manager	48
CPM: Configurable Pins	48
CPM: Groups	49
To Configure CPM Settings	50
Using Web Manager	50
Using the CLI	50
Using XML	50
9: Network Services	51
DNS Settings	51
To View or Configure DNS Settings:	51
Using Web Manager	51
Using the CLI	51
Using XML	51
FTP Settings	52
To Configure FTP Settings	52
Using Web Manager	52
Using the CLI	52
Using XML	52
Syslog Settings	52
To View or Configure Syslog Settings	53
Using Web Manager	53
Using the CLI	53
Using XML	53
HTTP Settings	53
To Configure HTTP Settings	54
Using Web Manager	54
Using the CLI	54
Using XML	54
To Configure HTTP Authentication	55
Using Web Manager	55
Using the CLI	55
Using XML	55
RSS Settings	55
To Configure RSS Settings	56
Using Web Manager	56
Using the CLI	56
Using XML	56
SNMP Settings	56
To Configure SNMP Settings	56
Using Web Manager	56
Using the CLI	57
Using XML	57
Discovery	57
To Configure Discovery	57
Using Web Manager	57
Using the CLI	57
Using XML	57
SMTP Settings	58
To Configure SMTP Settings	58
Using Web Manager	58
Using the CLI	58
Using XML	58
Email Settings	58
To View, Configure and Send Email	59
Using Web Manager	59
Using the CLI	59
Using XML	59
10: Updating Firmware	60
Obtaining Firmware	60
Loading New Firmware through Web Manager	60
To upload new firmware:	60
Loading New Firmware through FTP	61
11: Security Settings	62
Public Key Infrastructure	62
TLS (SSL)	62
Digital Certificates	63
Trusted Authorities	63
Obtaining Certificates	63
Self-Signed Certificates	63
Certificate Formats	63
OpenSSL	64
SSH Settings	64
SSH Server Host Keys	64
SSH Client Known Hosts	65
SSH Server Authorized Users	65
SSH Client Users	66
To Configure SSH Settings	67
Using Web Manager	67
Using the CLI	67
Using XML	67
SSL Settings	67
Certificate and Key Generation	67
To Create a New Credential	68
Using Web Manager	68
Using the CLI	68
Using XML	68
Certificate Upload Settings	69
To Configure an Existing SSL Credential	69
Using Web Manager	69
Using the CLI	69
Using XML	69
Trusted Authorities	70
To Upload an Authority Certificate	70
Using Web Manager	70
Using the CLI	70
Using XML	70
12: Maintenance and Diagnostics Settings	71
Filesystem Settings	71
File Display	71
To Display Files	71
Using Web Manager	71
Using the CLI	71
Using XML	71
File Modification	72
File Transfer	72
To Transfer or Modify Filesystem Files	73
Using Web Manager	73
Using the CLI	73
Using XML	73
Protocol Stack Settings	73
IP Settings	73
To Configure IP Protocol Stack Settings	73
Using Web Manager	73
Using the CLI	73
Using XML	73
ICMP Settings	74
To Configure ICMP Protocol Stack Settings	74
Using Web Manager	74
Using the CLI	74
Using XML	74
ARP Settings	74
To Configure ARP Network Stack Settings	74
Using Web Manager	74
Using the CLI	74
Using XML	74
Diagnostics	75
Hardware	75
To View Hardware Information	75
Using Web Manager	75
Using the CLI	75
Using XML	75
IP Sockets	75
To View the List of IP Sockets	75
Using Web Manager	75
Using the CLI	75
Using XML	75
Ping	75
To Ping a Remote Host	76
Using Web Manager	76
Using the CLI	76
Using XML	76
Traceroute	76
To Perform a Traceroute	76
Using Web Manager	76
Using the CLI	76
Using XML	76
Log	77
To Configure the Diagnostic Log Output	77
Using Web Manager	77
Using the CLI	77
Using XML	77
Memory	77
To View Memory Usage	77
Using Web Manager	77
Using the CLI	77
Using XML	77
Processes	78
To View Process Information	78
Using Web Manager	78
Using the CLI	78
Using XML	78
Threads	78
To View Thread Information	78
Using Web Manager	78
Using the CLI	78
Clock	78
To Specify Clock Setting Method	79
Using Web Manager	79
Using the CLI	79
Using the XML	79
System Settings	79
To Reboot or Restore Factory Defaults	80
Using Web Manager	80
Using the CLI	80
Using XML	80
13: Management Interface Settings	81
Command Line Interface Settings	81
Basic CLI Settings	81
To View and Configure Basic CLI Settings	81
Using Web Manager	81
Using the CLI	81
Using XML	81
Telnet Settings	82
To Configure Telnet Settings	82
Using Web Manager	82
Using the CLI	82
Using XML	82
XML Settings	82
XML: Export Configuration	82
To Export Configuration in XML Format	83
Using Web Manager	83
Using the CLI	83
Using XML	83
XML: Export Status	83
To Export in XML Format	84
Using Web Manager	84
Using the CLI	84
Using XML	84
XML: Import Configuration	84
Import Configuration from External File	84
Import Configuration from Filesystem	84
Line(s) from single line Settings on the Filesystem	84
To Import Configuration in XML Format	85
Using Web Manager	85
Using the CLI	85
Using XML	85
14: Branding the PremierWave SE1000 Device	86
Web Manager Customization	86
Short and Long Name Customization	87
To Customize Short or Long Names	87
Using Web Manager	87
Using the CLI	87
Using XML	87
Appendix A: Compliance	88
Appendix B: Lantronix Technical Support	90
Appendix C: Binary to Hexadecimal Conversions	91
Converting Binary to Hexadecimal	91
Conversion Table	91
Scientific Calculator	91