Home » Lantronix Manuals » Hubs & Switches » Lantronix SISPM1040-582-LRT » Manual Viewer

Lantronix SISPM1040-582-LRT Web User Guide Rev H PDF 15.20 MB - Page 64

Enabled, Disabled, SNMP v1, SNMP v2c, SNMP v3, Apply, Reset

View all Lantronix SISPM1040-582-LRT manuals

Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Lantronix SISPM1040-582-LRT Web User Guide Parameter descriptions: Mode : Indicates the SNMP mode operation. Possible modes are: Enabled: Enable SNMP mode operation. Disabled: Disable SNMP mode operation. Version : Indicates the SNMP supported version. Possible versions are: SNMP v1: Set SNMP supported version 1. SNMP v2c: Set SNMP supported version 2c (the default). SNMP v3: Set SNMP supported version 3. Read Community : Indicates the community read access string to permit access to SNMP agent. The allowed string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126. The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities table. It provides more flexibility to configure security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range of source addresses can be used to restrict source subnet. Write Community : Indicates the community write access string to permit access to SNMP agent. The allowed string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126. Enabled: Enable SNMP write community operation. Disabled: Disable SNMP write community operation. The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the community string will be associated with SNMPv3 communities table. It provides more flexibility to configure security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range of source addresses can be used to restrict source subnet. Engine ID : Indicates the SNMPv3 engine ID. The string must contain an even number (in hexadecimal format) with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed. Change of the Engine ID will clear all original local users. Buttons Apply : Click to save changes. Reset : Click to undo any changes made locally and revert to previously saved values. 33756 Rev. H https://www.lantronix.com/ Page 64 of 505

Section	Page
Contents	3
1 Introduction	7
1.2 About This Manual	8
1.3 Related Manuals	8
2 Web-based Management	9
2.1 Initial Login and Configuration	9
2.2 First Time Wizard	10
2.3 Startup Page	13
2.4 Webpage Controls	14
2.5 Webpage Messages	15
3 System Configuration	16
3.1 System	16
3.1.1 Information	16
3.1.2 IP	17
3.1.3 NTP	23
3.1.4 Time	25
3.1.5 Log	27
3.1.6 Digital I/O	28
3.1.7 Alarm Notification	30
3-2 Green Ethernet	34
3.2.1 Port Power Savings	34
3-3 Ports Configuration	36
3.3.1 Ports	36
3.3.2 Ports Description	38
3-4 DHCP	39
3.4.1 Server	39
3.4.2 Snooping	47
3.4.3 Relay	49
Summary – How to Set Up the Switch as a DHCP Server	50
3-5 Security	51
3.5.1 Switch	51
3.5.1.1 Users	51
3-5.2 Network	81
3-5.3 AAA	115
3-6 Aggregation	120
3-6.1 Static	120
3-6.2 LACP	122
3-6.3 LACP on Air	124
3-7 Link OAM	125
3-7.1 Port Settings	125
3-7.2 Event Settings	127
3-8 Loop Protection	129
3-9 Spanning Tree	131
3-9.1 Bridge Setting	132
3-9.2 MSTI Mapping	134
3-9.3 MSTI Priorities	136
3-9.4 CIST Port	137
3-9.5 MSTI Ports	139
3-10 IPMC Profile	141
3-10.1 Profile Table	141
3-10.2 Address Entry	144
3-11 MVR	145
3-12 IPMC	147
3-12.1 IGMP Snooping	147
3-12.2 MLD Snooping	154
3-13 LLDP	160
3-13.1 LLDP	160
2-13.2 LLDP-MED	163
3-14 PoE	168
3-14.1 Configuration	168
3-14.2 Power Delay	173
3-14.3 Schedule Profile	174
3-14.4 PoE Auto Power Reset	175
PoE Auto Checking “AutoFill” Feature	176
3-14.5 Chip Reset Schedule	177
3-15 EPS	178
3-16 MEP	182
3-17 ERPS	197
3-18 MAC Table	202
3-19 VLAN Translation	204
3-19.1 Port to Group Mapping	204
3-19.2 VID Translation Mapping	206
3-20 VLANs	208
3-21 Private VLANs	211
3-21.1 Membership	211
3-22.2 Port Isolation	213
3-23 VCL	214
3-23.1 MAC-based VLAN	214
3-23.2 Protocol-based VLAN	216
3-24 Voice VLAN	221
3-24.1 Configuration	221
3-24.2 OUI	223
3-25 Ethernet Services	224
3-25.1 Ports	224
3-25.2 L2CP	226
3-25.3 Bandwidth Profiles	227
3-25.4 EVCs	229
3-25.5 ECEs	232
3-26 QoS	235
3-26.1 Port Classification	235
3-26.2 Port Policing	239
3-26.3 Queue Policing	241
3-26.4 Port Scheduler	243
3-26.5 QoS Egress Port Shapers	245
3-26.6 Port Tag Remarking	246
3-26.7 Port DSCP	248
3-26.8 DSCP-Based QoS	250
3-26.9 DSCP Translation	252
3-26.10 DSCP Classification	254
3-26.11 QoS Control List	255
3-26.12 Storm Control	260
3-27 Mirroring	261
3-28 UPnP	265
3-29 PTP	266
3-30 GVRP	273
3-30.2 Port Config	275
3-31 sFlow	276
3-32 UDLD	278
3-33 Rapid Ring / Ring To Ring / Rapid Chain	280
3-33.2 Single Ring	282
3-33.3 Ring to Ring	283
3-33.4 Dual Ring	284
3-33.5 Rapid Chain	285
3-33.6 HW Setting and Status for Rings	286
3-36 ConsoleFlow and LPM	287
Supported Firmware Versions	287
ConsoleFlow Agent Configuration	287
3-37 MRP	291
3-38 SMTP	295
4. Monitor	296
4.1 Monitor > System > Information	296
4-1.2 IP Status	298
4-1.3 Log	300
4-1.4 Detailed Log	302
4-2 Green Ethernet	303
4-2.1 Port Power Savings	303
4-3 Ports	304
4-3.1 Traffic Overview	304
4-3.2 QoS Statistics	305
4-3.3 QCL Status	306
4-3.4 Detailed Statistics	308
4-3.5 SFP Information	310
3-3.6 SFP Detail Info	312
4-4 Link OAM	314
4-4.1 Statistics	314
4-4.2 Port Status	316
4-4.3 Event Status	318
4-5 DHCP	321
4-5.1 Server	321
4-5.2 Snooping Table	325
3-5.3 Relay Statistics	326
4-5.4 Detailed Statistics	328
4-6 Security	330
4-6.1 Access Management Statistics	330
4-6.2 Network	331
4-6.2.1 Port Security	331
4-6.3 AAA	346
4-6.4 Switch	353
4-7 Aggregation	359
4-7.1 Status	359
4-7.2 LACP	360
4-8 Loop Protection	363
4-9 Spanning Tree	364
4-10 MVR	369
4-11 IPMC	372
3-11.1 IGMP Snooping	372
4-12 LLDP	380
4-12.1 Neighbor	380
4-12.2 LLDP-MED Neighbor	382
4-12.3 PoE	386
4-12.4 EEE	387
4-12.5 Port Statistics	389
4-13 Ethernet Services	391
4-13.1 EVC Statistics	391
4-14 PTP	393
4-15 PoE	400
4-16 MAC Table	402
4-17 VLANs	404
4-17.1 Membership	404
4-17.2 Ports	406
4-18 MRP	408
4-19 VCL	410
4-19.1 MAC-based VLAN	410
4-19.2 Protocol-based VLAN	411
4-20 sFlow	415
4-21 UDLD	417
5. Diagnostics	418
5-1 Ping	418
5-2 Ping6	420
5-3 Cable Diagnostics	422
5-4 Traceroute	424
5-5 Link OAM	426
5-5.1 MIB Retrieval	426
6. Maintenance	427
6-1 Restart Device	427
6-2 Reboot Schedule	428
6-3 Factory Defaults	429
6-4 Firmware	430
6-4.1 Firmware Upgrade	430
6-4.2 Firmware Selection	431
6-5 Configuration	433
6-5.1 Save startup-config	433
6-5.2 Download	434
6-5.3 Upload	436
6-5.4 Activate	438
6-5.5 Delete	439
6-6 Server Report	440
7. DMS (Device Management System)	442
7.1 DMS > Management	442
7.1.1 DMS > DMS Mode	442
7.1.2 DMS Mode – DMS Controller Switch	444
7.1.3 DMS > Management > Map API Key	445
7.1.4 DMS > Management > Device List	446
7.2 DMS > Graphical Monitoring	448
7.2.1 DMS > Graphical Monitoring > Topology View	448
PoE Auto Power Reset “AutoFill” Feature	453
7.2.2 DMS Firmware Upgrade Procedure	454
7.2.3 DMS > Graphical Monitoring > Floor View	456
7.2.4 DMS > Graphical Monitoring > Map View	460
7.3 DMS > Maintenance	464
7.3.1 DMS > Maintenance > Floor Image	464
7.3.2 DMS > Maintenance > Diagnostics	469
7.3.3 DMS > Maintenance > Traffic Monitor	471
7.3.4 DMS Troubleshooting	473
8. Service, Warranty, and Tech Support	475
8.1 Recording Device and System Information	475
Appendix A. DHCP Per Port	477
A-1. Configure DHCP Per Port via the Web UI	477
A-2. DHCP Per Port Mode Configuration	478
Appendix B. MRP Pre-Requisites and Application Examples	481
B-1. MRP Description	481
B-2. MRP Operation	481
B-3. Related Devices	482
B-4. MRP Sample Setup	482
B-5. MRP Pre-Requisites (General)	482
B-6. MRP Web UI Configuration	483
Example 1: MRP Manager Re-Config (Web UI)	485
Example 2: Non-Blocking MRC State Recognized by MRM (Web UI)	486
Example 3: MRP Roles Set in Web UI	486
Appendix C – G.8032 Major and Sub Rings Configuration	487
Introduction	487
Basic Concepts	487
IP Addresses	487
Sample Configuration	488
Switch 1 Configuration (SISPM1040-582-LRT)	489
Switch 2 Configuration (SISPM1040-384-LRT-C)	490
Switch 3 Configuration (SISPM1040-362-LRT[W])	491
Switch 4 Configuration (SISPM1040-362-LRT[E])	492
Testing	493
Testing Pings from Switch 4 to Switch 1 – Major Ring	493
Testing Pings from Switch 4 to Switch 3 – Sub Ring	494
Config files	495
running-config_192.168.1	495
running-config_192.168.1	497
running-config_192.168.1	500

Match case Limit results 1 per page

Lantronix

SISPM1040-582-LRT Web User Guide

33756 Rev. H

https://www.lantronix.com/

Page

505

Parameter descriptions

Mode

: Indicates the SNMP mode operation. Possible modes are:

Enabled

: Enable SNMP mode operation.

Disabled

: Disable SNMP mode operation.

Version

: Indicates the SNMP supported version. Possible versions are:

SNMP v1

: Set SNMP supported version 1.

SNMP v2c

: Set SNMP supported version 2c (the default).

SNMP v3

: Set SNMP supported version 3.

Read Community

: Indicates the community read access string to permit access to SNMP agent. The allowed

string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126.

The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the

community string will be associated with SNMPv3 communities table. It provides more flexibility to configure

security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range

of source addresses can be used to restrict source subnet.

Write Community

: Indicates the community write access string to permit access to SNMP agent. The allowed

string length is 0 to 255 characters, and the allowed content is ASCII characters 33 - 126.

Enabled

: Enable SNMP write community operation.

Disabled

: Disable SNMP write community operation.

The field is applicable only when SNMP version is SNMPv1 or SNMPv2c. If SNMP version is SNMPv3, the

community string will be associated with SNMPv3 communities table. It provides more flexibility to configure

security name than a SNMPv1 or SNMPv2c community string. In addition to community string, a particular range

of source addresses can be used to restrict source subnet.

Engine

: Indicates the SNMPv3 engine ID. The string must contain an even number (in hexadecimal format)

with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed. Change of the Engine ID will

clear all original local users.

Buttons

Apply

: Click to save changes.

Reset

: Click to undo any changes made locally and revert to previously saved values.