Lantronix SRA Series Install Guide PDF 928.30 KB - Page 17

Use Serial port settings: Speed=115200, Parity=None, Data bits=8, Stop bits=1, HW Flow Control=No,

Get Lantronix SRA Series PDF manuals and user guides View all Lantronix SRA Series manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Lantronix Secure Remote Access (SRA) Install Guide RAD Setup 1. Connect Cat5/6 cable from PC to LAN1 port on RAD. 2. Open web browser and go to 192.168.1.10. 3. Login using default username/password: admin/admin. 4. Go to Network Configuration tab. 5. Fill in network configuration information. Click Apply. 6. Change PC IP address to work with new RAD IP address. 7. Log back into the RAD. 8. Go to Network Info tab and verify network information is correct. 9. Go to Configurations tab and assign a Site ID and select Update ID. 10. Go to Configurations tab and select Configure VPN. 11. Fill in Mgmt IP, Client IP, and Client count. (Note: Leave VPN Mode as "Disabled".) 12. Select Save VPN Config. 13. Go to Configurations tab and select Add MAP. 14. Fill in Internet facing IP, External Port, set Mode to VPN, set Status to Enabled in the order shown below. 15. Select Save MAP Config. You will now lose connection to the RAD unit. 16. Connect WAN1 and LAN1 into 192.168.2.0/24 network at the remote site. Caution: After app cfg is sent to reconfigure the RAD, edit the config file. Run the show rad command to verify the configuration via the console port. Note: The install process can be killed from the CLI with ctrl-c. Use Serial port settings: Speed=115200, Parity=None, Data bits=8, Stop bits=1, HW Flow Control=No, and SW Flow Control=No as console port settings for Command Line Interface (CLI) operation. Do not use the serial cable to update the firmware. When connecting to the serial port on SRA units, use a null modem cable with a female DB9 connector, such as the CABLE-SRA-NMC available through Lantronix. 33838 Rev. B https://www.lantronix.com/ Page 17 of 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Lantronix
Secure Remote Access (SRA) Install Guide
33838 Rev. B
Page
17
of
24
RAD Setup
1.
Connect Cat5/6 cable from PC to LAN1 port on RAD.
2.
Open web browser and go to 192.168.1.10.
3.
Login using default username/password: admin/admin.
4.
Go to Network Configuration tab.
5.
Fill in network configuration information. Click Apply.
6.
Change PC IP address to work with new RAD IP address.
7.
Log back into the RAD.
8.
Go to Network Info tab and verify network information is correct.
9.
Go to Configurations tab and assign a Site ID and select Update ID.
10.
Go to Configurations tab and select Configure VPN.
11.
Fill in Mgmt IP, Client IP, and Client count. (Note:
Leave VPN Mode as “Disabled”.)
12.
Select Save VPN Config.
13.
Go to Configurations tab and select Add MAP.
14.
Fill in Internet facing IP, External Port, set Mode to VPN, set Status to Enabled in the order shown below.
15.
Select Save MAP Config.
You will now lose connection to the RAD unit
.
16.
Connect WAN1 and LAN1 into 192.168.2.0/24 network at the remote site.
Caution
: After app cfg is sent to reconfigure the RAD, edit the config file. Run the show rad command to verify the
configuration via the console port.
Note
:
The install process can be killed from the CLI with ctrl-c.
Use Serial port settings: Speed=115200, Parity=None, Data bits=8, Stop bits=1, HW Flow Control=No, and
SW Flow Control=No as console port settings for Command Line Interface (CLI) operation. Do not use the serial cable
to update the firmware. When connecting to the serial port on SRA units, use a null modem cable with a female DB9
connector, such as the CABLE-SRA-NMC available through Lantronix.