Lantronix WiPort NR WiPort NR - User Guide - Page 53

Default Settings, Enable Enhanced Password, Disable Port 77F0 Hex, Channel 1 Configuration

Get Lantronix WiPort NR PDF manuals and user guides View all Lantronix WiPort NR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

5: Configuration via Serial Mode or Telnet Port Change key Enter key Select to modify the current AES encryption key. The default is N (No). If you selected Change Key, enter the key (at the Enter Key prompt) in hexadecimal numbers. Enter 32 characters for 128 bits key length, 48 characters for 192 bits key length, or 64 characters for 256 bits key length. Encryption only applies to the port selected for data tunneling (default 10001), regardless of whether you are using TCP or UDP. Generally, one of two situations applies:  Encrypted WiPort NR to WiPort NR device communication. Be sure to configure both devices with the same encryption key.  Third-party application to WiPort NR -encrypted communication: WiPort NR device uses standard AES encryption protocols. To communicate successfully, products and applications on the peer side must use the same protocols and the same encryption key as the WiPort NR serial-to-Ethernet device server. Lantronix Secure Com Port Redirector provides an encrypted connection from Windows-based applications to the WiPort NR device server. Information about SCPR is at http://www.lantronix.com/device-networking/utilities-tools/scpr.html. Enable Enhanced Password Setting enhanced password allows an extended security password of 16-characters for protecting Telnet access or Web Manager. N (No) is the default, which permits a 4-character password protecting Setup Mode by means of Telnet and web pages. Enable Enhanced Password (N) ? Disable Port 77F0 (Hex) Port 77F0 allows a custom application to query or set the eleven WiPort NR configurable pins when they are functioning as general purpose I/O (GPIO). Disable this capability, if desired, for security purposes. Disable Port 77F0h (N) ? The default setting, the N (No) option, enables GPIO control. The Y (Yes) option disables the GPIO control interface. Default Settings Select 7 Defaults from the Change Setup menu to reset the unit's Channel 1 configuration, Channel 2 configuration, E-mail settings, and Expert settings to the factory default settings. The server configuration settings for IP address, gateway IP address, and netmask remain unchanged. The configurable pins' settings also remain unchanged. The specific settings this option changes are listed below. Channel 1 Configuration Baudrate I/F Mode 9600 4C (1 stop bit, no parity, 8 bit, RS-232C, no flow control) WiPort® NR Embedded Device Server User Guide 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
5: Configuration via Serial Mode or Telnet Port
WiPort® NR Embedded Device Server User Guide
53
Change key
Select to modify the current AES encryption key. The default is
N
(No).
Enter key
If you selected
Change Key
, enter the key (at the
Enter Key
prompt) in hexadecimal numbers. Enter 32 characters for 128 bits
key length, 48 characters for 192 bits key length, or 64 characters
for 256 bits key length.
Encryption only applies to the port selected for data tunneling (default 10001),
regardless of whether you are using TCP or UDP.
Generally, one of two situations applies:
Encrypted WiPort NR to WiPort NR device communication. Be sure to configure
both devices with the same encryption key.
Third-party application to WiPort NR -encrypted communication: WiPort NR
device uses standard AES encryption protocols. To communicate successfully,
products and applications on the peer side must use the same protocols and the
same encryption key as the WiPort NR serial-to-Ethernet device server.
Lantronix Secure Com Port Redirector provides an encrypted connection from
Windows-based applications to the WiPort NR device server. Information about
SCPR is at
.
Enable Enhanced Password
Setting enhanced password allows an extended security password of 16-characters
for protecting Telnet access or Web Manager.
N
(No) is the default, which permits a
4-character password protecting Setup Mode by means of Telnet and web pages.
Enable Enhanced Password (N) ?
Disable Port 77F0 (Hex)
Port 77F0 allows a custom application to query or set the eleven WiPort NR
configurable pins when they are functioning as general purpose I/O (GPIO). Disable
this capability, if desired, for security purposes.
Disable Port 77F0h (N) ?
The default setting, the
N
(No) option, enables GPIO control. The
Y
(Yes) option
disables the GPIO control interface.
Default Settings
Select
7 Defaults
from the Change Setup menu to reset the unit’s Channel 1
configuration, Channel 2 configuration, E-mail settings, and Expert settings to the
factory default settings. The server configuration settings for IP address, gateway IP
address, and netmask remain unchanged. The configurable pins’ settings also
remain unchanged. The specific settings this option changes are listed below.
Channel 1 Configuration
Baudrate
9600
I/F Mode
4C (1 stop bit, no parity, 8 bit, RS-232C, no flow
control)