Lasko CT22766 User Manual - Page 3

MODELO CT22766 CONTROL REMOTO: Todas las funciones ejecutadas con el Control Remoto funcionan idénticamente a los controles manuales.(Figura 4) 1. Instale las dos baterías "AAA" (no incluidas). 2. No mezcle baterías viejas y nuevas. No mezcle baterías alcalinas, estándar (carbono-cinc), recargables (níquel-cadmio) o de iones de litio. 3. NO SE DESHÁGA DE BATERÍAS EN EL FUEGO. BATERÍAS PUEDEN ESTALLAR O PUEDEN SALIRSE. Vista de frente del Control Remoto Vista posterior del Control Remoto Figura 4 Retire el tornillo antes de la instalación de las baterías Si usted pierde su mando a distancia, por favor Cliente de llamada Serive para ordenar un reaplacement en 1-800 -233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p.m. (Horario Estándar del Este de los Estados Unidos). MODEL CT22766 OPERATION 1. Carefully remove the Heater from the bag and the carton. 2. Place the Heater on a firm, level surface. Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors. 3. Plug the cord set into a 120 volt outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. 4. When the Heater is initially plugged in, there will be a "beep" and the Power Light will come on indicating that there is power to the unit. The Power Light will remain lit until the Heater is unplugged from the electrical outlet. 5. Turn the Heater ON by pressing the Power Button ( ). 6. Press the ( ) and ( ) buttons at the same time to change the display to ° Celsius. Press the same two buttons together again to change the display back to ° Fahrenheit. 7. Upon turning the Heater on, the unit will be in HIGH heat (1500 Watts) (Figure 1). 8. Press the ( ) button for LOW heat. 9. To turn the Heater OFF, press the Power Button ( ) and unplug the Heater from the electrical outlet. Display when initially turned on OSCILLATE Figure 1 OSCILLATION: Pressing the Oscillate Button will allow the Heater to oscillate back and forth. To stop the oscillation, press the Oscillate Button again. When the Heater is in Automatic Temperature Control, the oscillation function will stop when the set temperature is reached and resume when the Heater turns back on. TIMER FUNCTION: The timer function may be activated when the Heater display is in any function or speed. (Figure 2) This function allows you to set the length of time the Heater will run before turning itself off, from 1 hour to 8 hours. Pressing the Timer Button ( ) will increase the length of time by 1 hour each time this button is pressed. After the display reflects 8 hours, pressing the Timer Button ( ) once more will reset the Heater to run continuously. The Heater will turn off when the set time has elapsed. The unit can be turned back on by pressing the Power Button ( ). Timer Function in Low Heat OSCILLATE Figure 2 AUTOMATIC TEMPERATURE CONTROL (Figure 3) The automatic temperature function will only operate on "High" heat. You cannot set the temperature automatically when the unit is in the low heat mode. 1. To set the room at a specific temperature press the ( ) or ( ) buttons to the desired temperature. The display will now reflect the ( ) and the temperature will be flashing. The Heater is now in Auto Temperature Mode. 2. When you reach the temperature at which you want to set the unit, the set temperature will flash several times and then the display will return to indicate the current room temperature and will gradually change as the room temperature changes. NOTE: the temperature display does not indicate the temperature of the heated air being emitted by the heater. 3. Once the room temperature reaches 2 degrees above the set temperature, the Heater will shut off. Once the room temperature reaches 1 degree below the set temperature, the Heater will turn back on and continue to cycle off and on to maintain the set temperature. 4. This function will cancel if the ( ) button is pressed. The Heater will now be in High heat and run continuously. NOTE: It is normal for the Heater "fan" to run for approximately 15 seconds when the Heater shuts off after reaching the set temperature. Display reflects High Heat and Automatic Temperature Control Function OSCILLATE New 4/13 10 CT22766ES New 4/13 Figure 3 3 CT22766ES