Lasko T42950 User Manual - Page 4
Modelo T42950, Model T42950
View all Lasko T42950 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
MODEL T42950 OPERATION This Fan may be operated by the manual controls located on top of the unit (as shown in Figure 3) or by the Remote Control (shown in Figure 4). 1. Remove the Fan from the carton and assemble as instructed. 2. Place the Fan on a firm and level surface. CAUTION: Plastic or rubber tabs, like the feet on this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken, stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or hardwood floors. 3. Plug the cord set into a 120 volt outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely into receptacles, they may slip partially or completely out of the receptacle with only the slight movement of the attached cord. Receptacles in this condition may overheat and pose a serious fire hazard; if covered by a curtain or drape, the fire hazard is even greater. 4. Turn the Fan on by pressing the Power Button ( ). A light will appear when the Fan is turned on. This light will remain lit until the unit is turned off. 5. SPEEDS: Press the Fan Speed Button ( ) to desired speed setting. Each time the Fan Speed Button is pressed, the speed will change from high (3), to medium (2), to low (1). 6. OSCILLATION: Press the Oscillation Button ( ) to start and stop the oscillation function. 7. TIMER: The timer function allows the unit to be set to operate for a length of time from 1/2 hour to 7 1/2 hours, in increments of a 1/2 hour. Press the Timer Button ( ) to set the length of time desired. Each time the timer button is pressed, the time is increased by 1/2 hour. After reaching 7 1/2 hours, pressing the timer button once more will reset the Fan to continuous running. The lights on the front of the unit will light up appropriately with the length of time that the Fan is set for. 8. IONIZER: The ionizer function on this Fan will operate within any speed mode. Press the Ion Button once to turn this function on and a second time to turn it off. The Fan must be ON for the ionizer to be functional. When the ionizer is turned on it will assist in the purification of the room air. 9. To turn the Fan OFF, press the Power Button ( ). 10.After turning the Fan off, unplug the unit from the electrical outlet. Ionizer Button Timer Button Oscillation Button Fan Speed Button Power Button Figure 3 MODELO T42950 HERRAMIENTAS NECESARIAS PARA EL ARMADO (no incluida) - Destornillador de Cabeza Phillips # 2 ARMADO 1. Para un armado más sencillo, deposite el Ventilador hacia abajo para que la parrilla frontal y el panel de control apunten hacia arriba. 2. Arme las Mitades de la Base de Apoyo encastrando las Puntas de la Base de Apoyo A con los Orificios para Puntas en la Base de Apoyo B. Conecte el Cable Eléctrico a través del orificio grande en el centro de la Montura de la Base de Apoyo. (Figura 1) 4. Alinee la Montura de la Base de Apoyo con la Base del Motor, teniendo en cuenta que la ranura del cable en la parte inferior de la montura de la base de apoyo debe apuntar hacia la parte posterior del Ventilador. Adose la Montura de la Base de Apoyo a la Base del Motor con (4) Tornillos Mariposa. Cerciórese de alinear la Llave del Conjunto de la Base de Soporte con la Muesca Localizadora de la Base Del Motor. (Figura 1) Suavemente tire del Cable Eléctrico para evitar que quede flojo y colóquelo en el Orificio de Colocación del Cable. (Figura 2) Puntas de la Base de Apoyo A Llave Montura de la Base de Apoyo Puntas Puntas de la Base de Apoyo B Figura 1 3. Asegure (2) #8 X 3/8" (9.52 mm) Tornillos en los dos orificios externos en la parte inferior de la Base. (Figura 2) Cable Eléctrico Orificio de Colocación del Cable Figura 2 NEW 1/18 4 T42950ES NEW 1/18 9 T42950ES