Lasko YF200 User Manual - Page 2

WARNING IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, these instructions and warnings should always be followed to reduce the risk of fire, electrical shock and injury to persons: Read all instructions before using this Fan. WARNING TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS: DO NOT use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the containers for these products! ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should be replaced by a qualified electrician. ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan when not in use. BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source. The Blue Plug™ on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug. The power cord is equipped with a three-prong, grounded GFCI (Ground Fault Circuit Interrupter) plug that must be inserted into a grounded receptacle. Under no circumstances must the grounding prong be cut off the plug. WARNING: Do not use a three-prong to two-prong adapter. Where a two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only. The GFCI Fan cord set can be plugged into an existing GFCI outlet if present. RISK OF ELECTRIC SHOCK. TEST GFCI PLUG BEFORE EACH USE. PLUG GFCI INTO POWER OUTLET. INDICATOR LIGHT SHOULD TURN ON. PRESS TEST BUTTON. INDICATOR LIGHT SHOULD TURN OFF. PRESS AND RELEASE RESET BUTTON. INDICATOR LIGHT SHOULD TURN ON. If above test fails, DO NOT USE THIS GFCI FAN. USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT PERMITTED. IMPROPER CONNECTION MAY CREATE THE RISK OF ELECTRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA. This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT remove, replace, repair or tamper with the originally supplied plug or GFCI. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. Call 800-233-0268, Monday - Friday, between 8:00 a.m. and 5:00 p.m. Eastern. If the plug warning label is missing or damaged, call the toll free number for a replacement label. CAUTION WARNING RISK OF ELECTRIC SHOCK. TEST GFCI PLUG BEFORE EACH USE. 1. PLUG GFCI INTO POWER OUTLET. INDICATOR LIGHT SHOULD TURN ON. 2. PRESS TEST BUTTON. INDICATOR LIGHT SHOULD TURN OFF. 3. PRESS AND RELEASE RESET BUTTON. INDICATOR LIGHT SHOULD TURN ON. IF ABOVE TEST FAILS, DO NOT USE THIS GFCI FAN. CALL 800-233-0268, MON - FRI, 8:00 A.M. AND 5:00 P.M. EASTERN • AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these devices may overheat and cause a fire hazard. • DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard. • ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning. • NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur. • DO NOT block, cover or obstruct air flow to or from the Fan while in operation. • DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. • NEVER use a single extension cord to operate more than one Fan or other electrical device. • DO NOT use this Fan if it has been damaged or is not functioning properly. • Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs, move the Fan to another location. • Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan. • THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings. • THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for hazardous locations. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. Rev. A 1/20 SAVE THESE INSTRUCTIONS 2 YF200_YF202ES Partes Incluidas 1 1 Cuerpo 2 Support Base A 3 Support Base B Ensamblaje 1. Empuje a los Ranuras del Jefe en la Base de Soporte A en las Jefes en la Base de Soporte B abajo hasta que haga clic. Controles Botón de Encendido ENCENDIDO/APAGADO el Ventilador presionando el Botón de Encendido Botón de Oscilación Interna Presione el Botón de Oscilación para ini- ciar y detener la función de oscilación. Rev. A 1/20 7 2 3 2. Alinee el Cuerpo con la Base de Soporte. Empuje hacia abajo hasta que haga clic. Botón de Velocidad La velocidad del ventilador se puede ajustar a 4, 3, 2, o Nota: es baja velocidad Botón de Bluetooth (Modelo YF200) Presione para activar la función Bluetooth (Para ver una descripción detallada de la sincronización Bluetooth®, consulte la guía de inicio rápido) YF200_YF202ES