Lenovo 4014HB6 User Guide - Page 26

Manual image setup - problem

Get Lenovo 4014HB6 PDF manuals and user guides View all Lenovo 4014HB6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Table3-2.Troubleshooting(continued) Problem Possible cause Suggested action Screen is blank The monitor is in and power Standby/Suspend indicator is mode steady amber or flashing green The power indicator is green, but there is no image. The video signal cable is loose or disconnected from the system or monitor. The monitor brightness and contrast are at the lowest setting. ● Press any key on the keyboard or move the mouse to restore operation. ● Check the Power Options settings on your computer. Be sure the video cable is connected with the system properly. Adjust the brightness and contrast setting on the OSD menu. One or more of This is a the pixels characteristic of the appear LCD technology discolored and is not an LCD defect. If there are more than five pixels missing, contact the Customer Support Center. ● Fuzzy lines in ● Image setup Adjust the resolution text or a has not been settings on your system blurry optimized to match the native image. ● Your system resolution for this ● Horizontal or Display Properties monitor: 1920x1080 at 60 vertical lines setting have Hz. through the image. not been optimized. Perform automatic image setup. If automatic image setup does not help, perform manual image setup. Reference "Understanding power management" on page 2-10 "Connecting and turning on your monitor" on page 1-4 "Adjusting your monitor image" on page 2-3 Appendix A, "Service and Support," on page A-1 "Adjusting your monitor image" on page 2-3 "Manual image setup" "Selecting a supported display mode" on page 2-10 When working in the native resolution, you may find additional improvements by adjusting the Dots Per Inch (DPI) setting on your system. See the Advanced section of your system's display properties. The image is It has not set the out of shape optimum resolution when switching for each mode to dual mode ● Use ThinkVision Duo software to optimize the dual screen operation ● Adjust graphic card resolution manually "Using the ThinkVision Duo software control" on page 2-4 "Using the direct access controls" on page 2-3 Manual image setup If automatic image setup does not establish the image that you prefer, perform manual image setup. Note: Have your monitor powered on for about 15 minutes, until the monitor warms up. 1. Press at the bottom of the monitor to open the OSD menu. 2. Use or to select and press to access. 3. Use or to select Clock and Phase adjustment. Chapter 3. Reference information 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
Table3-2.Troubleshooting(continued)
Problem
Possible cause
Suggested action
Reference
Screen is blank
and power
indicator is
steady amber
or flashing
green
The monitor is in
Standby/Suspend
mode
●
Press any key on the
keyboard or move the
mouse to restore
operation.
●
Check the Power
Options settings on
your computer.
“Understanding power
management” on page
2-10
The video signal
cable is loose or
disconnected from
the system or
monitor.
Be sure the video cable is
connected with the
system properly.
“Connecting and turning
on your monitor” on
page 1-4
The power
indicator is
green, but
there is no
image.
The monitor
brightness and
contrast are at
the lowest setting.
Adjust the brightness and
contrast setting on the OSD
menu.
“Adjusting your monitor
image” on page 2-3
One or more of
the pixels
appear
discolored
This is a
characteristic of the
LCD technology
and is not an LCD
defect.
If there are more than
five pixels missing,
contact the Customer
Support Center.
Appendix A, “Service and
Support,” on page A-1
Adjust the resolution
settings on your system
to match the native
resolution for this
monitor: 1920x1080 at 60
Hz.
“Adjusting your monitor
image” on page 2-3
“Manual image setup”
Perform automatic image
setup. If automatic image
setup does not help,
perform manual image
setup.
“Selecting a supported
display mode” on page
2-10
●
Fuzzy lines in
text or a
blurry
image.
●
Horizontal or
vertical lines
through the
image.
●
Image setup
has not been
optimized
●
Your system
Display Properties
setting have
not been
optimized
.
When working in the
native resolution, you
may find additional
improvements by
adjusting the Dots Per
Inch (DPI) setting on
your system.
See the Advanced section
of your system’s display
properties.
The image is
when switchin
out of shape
g
to dual mode
the
optimum resolution
It has not set
●
Use ThinkVision Duo
software to optimize the dual
screen operation
●
Adjust graphic card
resolution manually
“Using the ThinkVision
Duo software control” on
page 2-4
“Using the direct access
controls” on page 2-3
Manual image setup
If automatic image setup does not establish the image that you prefer, perform
manual image setup.
Note: Have your monitor powered on for about 15 minutes, until the monitor
warms up.
1.
Press
at the bottom of the monitor to open the OSD menu.
2.
Use
or
to select
and press
to access.
3.
Use
or
to select
Clock
and
Phase
adjustment.
Chapter 3. Reference information
3-3
for each mode