Lenovo 926503U User Manual - Page 50

Installing, drive

Get Lenovo 926503U - ThinkCentre A55 - 9265 PDF manuals and user guides
UPC - 883609529888
View all Lenovo 926503U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the computer cover. See "Removing the cover" on page 20. 2. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the bezel outward. Carefully set the bezel to the side without disconnecting the power switch and LED assembly cable. Note: Notice the spare retainer bracket 1 attached to the side of the upper drive cage. 3. Remove the metal static shield from the drive bay using your fingers to pull it outward. 4. If you are installing a drive with accessible media, such as an optical drive, remove the plastic panel in the bezel for bay 2 by squeezing the plastic tabs that secure the panel on the inside of the bezel. 5. If you are installing any type of drive other than a serial ATA hard drive, make sure the drive that you are installing is set correctly as either a master or a slave device. Note: A serial ATA hard disk drive does not need to be set as either a master or a slave device. If you are installing an optical drive or a parallel ATA hard disk drive, set it as a master device. Refer to the documentation that comes with your drive for master/slave jumper information. 6. Remove the retainer bracket from the upper driver cage by sliding it downward. 30 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Installing
a
drive
in
bay
1
or
bay
2
To
install
a
drive
in
bay
1
or
bay
2,
follow
these
steps:
1.
Remove
the
computer
cover.
See
“Removing
the
cover”
on
page
20.
2.
Remove
the
front
bezel
by
releasing
the
three
plastic
tabs
on
the
left
side
and
pivoting
the
bezel
outward.
Carefully
set
the
bezel
to
the
side
without
disconnecting
the
power
switch
and
LED
assembly
cable.
Note:
Notice
the
spare
retainer
bracket
±1²
attached
to
the
side
of
the
upper
drive
cage.
3.
Remove
the
metal
static
shield
from
the
drive
bay
using
your
fingers
to
pull
it
outward.
4.
If
you
are
installing
a
drive
with
accessible
media,
such
as
an
optical
drive,
remove
the
plastic
panel
in
the
bezel
for
bay
2
by
squeezing
the
plastic
tabs
that
secure
the
panel
on
the
inside
of
the
bezel.
5.
If
you
are
installing
any
type
of
drive
other
than
a
serial
ATA
hard
drive,
make
sure
the
drive
that
you
are
installing
is
set
correctly
as
either
a
master
or
a
slave
device.
Note:
A
serial
ATA
hard
disk
drive
does
not
need
to
be
set
as
either
a
master
or
a
slave
device.
If
you
are
installing
an
optical
drive
or
a
parallel
ATA
hard
disk
drive,
set
it
as
a
master
device.
Refer
to
the
documentation
that
comes
with
your
drive
for
master/slave
jumper
information.
6.
Remove
the
retainer
bracket
from
the
upper
driver
cage
by
sliding
it
downward.
30
User
Guide