Lenovo C260 Lenovo C260 All-In-One PC Hardware Maintenance Manual
Lenovo C260 Manual
View all Lenovo C260 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lenovo C260 manual content summary:
- Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 1
Lenovo C260 All-In-One PC Hardware Maintenance Manual ideaideaideaCentreidea Machine Types: 10160/F0AK [C260] - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 2
- Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 3
Lenovo C260 All-In-One PC Hardware Maintenance Manual Machine Types: 10160/F0AK [C260] - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 4
First Edition (February 2014)25th © Copyright Lenovo 2013, 2014. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925 - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 5
1. About this manual 1 Important Safety Information 1 Chapter 2. Safety information 3 General safety 3 Electrical safety 3 Safety inspection guide 5 Handling electrostatic board 39 Replacing the LED panel 41 Chapter 8. Additional Service Information 45 © Copyright Lenovo 2013, 2014 iii - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 6
iv Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 7
manual This manual contains service and reference information for Lenovo C260 All-In-One computer listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo in this manual before following any of the instructions. Veuillez - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 8
2 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 9
attaching springs, using solvents, or working in any other conditions that might be hazardous to your eyes. • After service, reinstall all safety shields, guards, the computer covers, unless instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2013, 2014 3 - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 10
special safety precautions when you work with very high voltages; these instructions are in the safety sections of and touching a live circuit can cause personal injury and damage to the computer. • Do not service the victim yourself. 4 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 11
installed to protect users and service personnel from injury. This guide addresses only those items. However you can continue without first resolving the problem. Consider the following items and the the charge so that the computer, the part, the work mat, and the person handling the part are all - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 12
the device covers, unless instructed otherwise in the installation and configuration procedures. • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. 6 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 13
: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 14
are disconnected from the power source. 2 1 CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. 8 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 15
that applies to all computer models covered by this manual. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo C260 This section lists the physical specifications. Environment Air temperature - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 16
10 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 17
servicing error messages appear if a problem or conflict is found by determine the cause of the problem: 1. Power-off the displayed error codes. • Look for readable instructions or a main menu on the display. If one of the following happens, follow the instruction given: • If the computer displays a - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 18
12 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 19
Setup Utility menu. The keys used to perform various tasks are displayed on the bottom of each screen. Using passwords You can use the Lenovo BIOS Setup Utility program to set passwords to prevent unauthorized persons from gaining access to your computer and data. See "Starting the Setup Utility - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 20
blank, then press the Enter key. A Setup Notice will be displayed confirming that your changes have been saved. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save Changes and Exit from the menu. 14 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 21
, then press the Enter key. 4. Retype the password to confirm. If you typed the password correctly, the password will be installed. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save Changes and Exit from the menu. To change a Power-On Password, do the - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 22
Controller Onboard Ethernet Controller or LAN Boot Agent Select Disabled/IDE/AHCI mode. Device driver support is required for AHCI or RAID. Depending on how the hard disk drive Device Menu does not permanently change the startup sequence. 16 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 23
screen. 4. Use - and ¯ arrows to select a device. Use the or keys to move a device up or down. Use the key to exclude the device from or include the device in the boot sequence. 5. Return to the Lenovo must change the boot mode to Legacy support. The legacy Windows operating system cannot - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 24
18 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 25
used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to "Undetermined problems" on page 20. Notes: • If you have both an FRU/Action Reseat connectors Power Cord Power-on Switch © Copyright Lenovo 2013, 2014 19 - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 26
motherboard operations • Checks that the memory is working correctly • Starts video operations • Verifies that the boot drive is working POST Error Message Keyboard error have been removed and the problem continues, replace the system board. 20 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 27
with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://support.lenovo.com. Note: Use only parts provided by Lenovo. General information Pre-disassembly instructions Before starting the disassembly procedure, make sure that you do the following - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 28
adapter: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Locate the connector for the power cord. Refer to "Rear view". 22 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 29
Step 3. Disconnect the failing power adapter from the computer. Step 4. To install the new power adapter: a. Connect the new power adapter to the same connector. Chapter 7. Replacing hardware 23 - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 30
Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and connectors. Use a flat head screw driver to remove the stand cover as shown. 24 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 31
Step 5. Remove the 2 screws that secure the computer stand to the rear cover. Step 6. Slide out the computer stand as shown. Step 7. To install the new computer stand: a. Line up the computer stand with the mounting hole on the rear cover and slide it into position. b. Secure the new computer - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 32
Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage. To remove the rear cover: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 33
Step 5. Lift up the rubbers that protect the 2 screws, remove the 2 screws that secure the rear cover to the front Step 6. bezel. The rear cover and front bezel are pinned together, use a plastic flat-head screwdriver, insert to the gap in-between the rear cover and the front bezel, slide the - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 34
optical drive: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached rear cover, refer to "Removing the rear cover". 28 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 35
Step 5. Slide out the optical drive as shown. Step 6. Use a small flat head screwdriver to press and push out the pins that secure the cover to the disk. 4 5 Step 7. Separate the cover from the defective optical drive. Step 8. Install the new optical drive as follows: a. Align the new optical - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 36
the hard disk drive: Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. 30 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 37
Step 3. Step 4. Step 5. Step 6. Step 7. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to "Left and right view" and "Rear view" for help with locating the various connectors. Remove - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 38
2. Step 3. Step 4. Step 5. Step 6. Step 7. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. the rear cover. To replace the speaker system: 32 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 39
Step 5. Step 6. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn the indicator board [A60110] Error in document "D:\All Pros\C260\HMM\Lenovo C260 Hardware Maintainence Manual.ditamap" on reference (topicref) element at line 81: Unable - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 40
system fan: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached rear cover. Refer to "Removing the rear cover". 34 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 41
" and "Rear view" for help with locating the various connectors. Remove the rear cover. Refer to "Removing the rear cover". Remove all memory modules. Refer to "Replacing a memory module". Remove the heat-sink. Refer to "Replacing the heat-sink". Remove the Wi-Fi card. Refer to "Replacing the Wi-Fi - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 42
shown. Step 11. To install the new motherboard: a. Attach the heat-sink, Wi-Fi card, memory modules to the new motherboard. b. Line up the holes on the new motherboard with the mounting holes . Reattach the rear cover, stand and stand cover. 36 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 43
removing the rear cover. To replace the heat-sink: Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Step 7. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Unplug all power cords from electrical - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 44
the camera: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached rear cover. Refer to "Removing the rear cover". 38 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 45
Step 5. Remove the 2 screws that secure the camera to the front bezel. Step 6. Gently slide out the camera and disconnect the cable from the camera. Step 7. To install the new camera: a. Connect the data cable to the new camera. b. Line up the holes in the new camera with the mounting holes on the - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 46
Step 3. Step 4. Step 5. Step 6. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all converter board to remove it. Step 8. To install the new converter board: 40 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 47
before removing the rear cover. To replace the LED panel: Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Unplug all power cords from electrical - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 48
Step 7. Disconnect the LVDS and converter cables from the connector on the LED panel. 42 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 49
Step 8. Remove the 7 screws that secure the LED panel to the front bezel. The LED panel is glued to the front bezel, gently remove the LED panel from the front bezel. Step 9. Remove the 4 screws that secure the LED panel to the bracket to separate the LED panel from the bracket. Step 10. To install - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 50
Step 11. Reattach the converter board, camera, rear cover, stand and stand cover. 44 Lenovo C260 All-In-One PC Hardware Maintenance Manual - Lenovo C260 | Lenovo C260 All-In-One PC Hardware Maintenance Manual - Page 51
provides additional information that the service representative might find helpful. Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode. Automatic Power-On features The Automatic Power-On adapter card to wake the System. © Copyright Lenovo 2013, 2014 45
Lenovo C260 All-In-One PC Hardware
Maintenance Manual
Machine Types: 10160/F0AK [C260]