Lenovo H30-00 Lenovo H30 Series Hardware Maintenance Manual - Page 22

Selecting a startup device, Startup Device Menu - bios

Get Lenovo H30-00 PDF manuals and user guides View all Lenovo H30-00 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Onboard Audio Controller Onboard Ethernet Controller or LAN Boot Agent Select whether to enable or disable the Onboard Audio Controller, when feature is set to Disabled all devices connected to the audio connectors (e.g. a headphone or a microphone) are disabled and can't be used. Select whether to enable or disable Onboard Ethernet Controller, or select whether to enable or disable load onboard PXE (Preboot Execution Environment), or SMC (Secure Managed Client). This feature will allow the computer to boot from a server image. To enable or disable a device, do the following: 1. Start the Setup Utility program (see "Starting the Setup Utility program" on page 13). 2. From the Setup Utility program menu, select Devices. 3. Select: Serial Port Setup press the Enter key, and then select Serial Port Setup. USB Setup press the Enter key, and then select USB Functions. ATA Device Setup press the Enter key. Select Configure SATA as, press the Enter key and then select SATA mode. Video Setup press the Enter key, and then select Video Setup. Audio Setup press the Enter key, and then select Onboard Audio Controller. Network Setup press the Enter key, then select Onboard Ethernet Support or LAN Boot Agent. 4. Select Disabled or Enabled and press the Enter key. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save changes and Exit from the menu. Note: If you do not want to save the settings, select Discard changes and Exit from the menu. Selecting a startup device If your computer does not boot from a device such as the CD/DVD-ROM drive disk or hard disk as expected, follow one of the procedures below. Selecting a temporary startup device Use this procedure to startup from any boot device. Note: Not all CDs, DVDs or hard disk drives are bootable. 1. Turn off your computer. 2. Press and hold the F12 key then turn on the computer. When the Startup Device Menu appears, release the F12 key. Note: If the Startup Device Menu does not display using these steps, repeatedly press and release the F12 key rather than keeping it pressed when turning on the computer. 3. Use ↑ and ↓ arrows to select the desired startup device from the Startup Device Menu and press the Enter key to begin. Note: Selecting a startup device from the Startup Device Menu does not permanently change the startup sequence. Selecting or changing the startup device sequence 16 Lenovo H30 SeriesHardware Maintenance Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Onboard Audio Controller
Select whether to enable or disable the
OnboardAudio
Controller
, when feature is set to Disabled all devices
connected to the audio connectors (e.g. a headphone or
a microphone) are disabled and can’t be used.
OnboardEthernetControllerorLANBootAgent
Select whether to enable or disable
OnboardEthernet
Controller
, or select whether to enable or disable load
onboard
PXE
(
Preboot Execution Environment
), or
SMC
(
SecureManagedClient
). This feature will allow
the computer to boot from a server image.
To enable or disable a device, do the following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 13).
2. From the Setup Utility program menu, select
Devices
.
3. Select:
SerialPortSetup
press the
Enter
key, and then select
SerialPortSetup
.
USBSetup
press the
Enter
key, and then select
USBFunctions
.
ATADeviceSetup
press the
Enter
key. Select
ConfigureSATAas
, press the
Enter
key and then
select SATA mode.
VideoSetup
press the
Enter
key, and then select
VideoSetup
.
AudioSetup
press the
Enter
key, and then select
OnboardAudioController
.
NetworkSetup
press the
Enter
key, then select
OnboardEthernetSupport
or
LANBootAgent
.
4. Select
Disabled
or
Enabled
and press the
Enter
key.
5. Return to the Lenovo BIOS Setup Utility program menu and select the
Exit
option.
6. Select
Save changes and Exit
from the menu.
Note:
If you do not want to save the settings, select
DiscardchangesandExit
from the menu.
Selecting a startup device
If your computer does not boot from a device such as the CD/DVD-ROM drive disk or hard disk as expected,
follow one of the procedures below.
Selecting a temporary startup device
Use this procedure to startup from any boot device.
Note:
Not all CDs, DVDs or hard disk drives are bootable.
1. Turn off your computer.
2. Press and hold the
F12
key then turn on the computer. When the
Startup Device Menu
appears,
release the
F12
key.
Note:
If the
StartupDeviceMenu
does not display using these steps, repeatedly press and release the
F12
key rather than keeping it pressed when turning on the computer.
3. Use
↑
and
↓
arrows to select the desired startup device from the
Startup Device Menu
and press
the
Enter
key to begin.
Note:
Selecting a startup device from the
StartupDeviceMenu
does not permanently change the
startup sequence.
Selecting or changing the startup device sequence
16
Lenovo H30 SeriesHardware Maintenance Manual