Lenovo IdeaCentre K210 K200 Hardware Maintenance Manual
Lenovo IdeaCentre K210 Manual
 |
View all Lenovo IdeaCentre K210 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lenovo IdeaCentre K210 manual content summary:
- Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 1
safety...4 Electrical safety...5 Safety inspection guide 7 Handling electrostatic discharge-sensitive devices 8 Grounding requirements 8 Safety notices...9 Chapter 3. General information 12 Specifications...12 Chapter 4. General Checkout 13 Problem determination tips 14 Chapter 5. Using - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 2
Manual Selecting a temporary startup device 20 Selecting or changing the startup device sequence 21 Exiting from the Setup Utility program 21 Chapter 6. Symptom-to-FRU Index 22 Hard disk drive boot error 22 Power Supply Problems 23 Beep symptoms 24 POST error codes 25 Undetermined problems - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 3
servicing a Lenovo product, be sure to read the Safety Information. This manual includes a complete FRU part number listing for each machine type and model listed on the cover. If you have internet access, FRU part numbers are also available at: http:/www.lenovo.com/support les instructions. Lesen - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 4
Manual Using eSupport For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) •• eSupport can be used to view the list of key commodities built in a particular machine serial. •• eSupport can be accessed at the following Web site: http://www.lenovo.com/support - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 5
Chapter 1. About this manual implementation date and expects its suppliers to be ready to support Lenovo's requirements and schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 6
Hardware Maintenance Manual Safety information 2 This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: •• Observe good housekeeping in the area of the machines during and after - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 7
be hazardous to your eyes. •• After service, reinstall all safety shields, guards, power cords, telecommunication systems, networks, and modems before you open the server/workstation covers, unless instructed all power before: - Performing a mechanical inspection - Working near power supplies - - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 8
safety precautions when you work with very high voltages; these instructions are in the safety sections of maintenance information. Use extreme •• Do not service the following parts with the power on when they are removed from their normal operating places in a machine: - Power supply units - Pumps - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 9
items installed to protect users and service personnel from injury. This guide addresses only those items. However guide consists of a series of steps presented in a checklist. Begin the checks with the power off, and the power that the power-supply cover fasteners (screws or rivets) have not been removed - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 10
Hardware Maintenance Manual Handling electrostatic discharge-sensitive devices Any computer part containing a grounding system, such as those listed below, to provide protection that meets the specific service requirement. Note: The use of a grounding system is desirable but not required to protect - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 11
when there is evidence of fire, water, or structural damage. •• Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures. •• Connect and disconnect cables as - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 12
Hardware Maintenance Manual CAUTION: When replacing the lithium battery, use only Part Number covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. •• Use of controls or adjustments or performance of procedures other than - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 13
CAUTION: Use safe practices when lifting. CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 14
Manual General information 3 This chapter provides general information that applies to all machine types supported by this publication. Specifications This section lists the physical specifications for your computer. Type Lenovo IdeaCentre K This section lists the physical specifications - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 15
servicing these messages, refer to the information supplied with that software package. Notes • BIOS is installed on the system. A down-level BIOS might cause false errors and unnecessary replacement of the system board. Use the following procedure to help determine the cause of the problem: 1. Power - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 16
Manual 5. Power-on the computer. • Look for displayed error codes • Listen for beep codes • Look for readable instructions problem determination. If possible, have this information available when requesting assistance from Service Support models 2. Have the same BIOS level 3. Have the same adapters - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 17
Chapter 4. General Checkout Comparing the configuration and software set-up between "working and non-working" systems will often lead to problem resolution. 15 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 18
Hardware Maintenance Manual Using the Setup Utility 5 The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 19
Chapter 5. Using the Setup Utility keyboard. The keys used to perform various tasks are displayed on the right side of each screen. Using passwords By using the Setup Utility program, you can set passwords to prevent unauthorized persons from gaining access to your computer and data. See "Starting - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 20
Hardware Maintenance Manual password. However, to change any configuration settings, you must use your supervisor password. Setting, changing, and deleting a Supervisor password To set, change, or delete a password, - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 21
is set, the Security Options can be displayed in the menu of Advanced BIOS Features. To set Security Options, do the following: 1. Start the Setup the Setup Utility program menu and select press ESC to return the Advanced BIOS Features or press F10 to Save configuration changes and exit setup. Notes: - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 22
Hardware Maintenance Manual Using Device Device is used to enable or disable user access Discard Changes. You can set others such as OnBoard SiS USB2.0 Controller, USB Keyboard Legacy Support, USB Mouse Legacy Support, Onboard Audio DEVICE, Onboard LAN Control, Boot from Onboard LAN and so on. See - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 23
(see "Starting the Setup Utility program" on page 16). 2. Select Advanced BIOS Features. 3. Select the devices for the 1st Boot Device, the 2nd Boot Deviece and the 4th Boot Device. 4. Press ESC to return the Advanced BIOS Features and then Save changes and Exit. If you have changed these settings - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 24
page 13. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to "Undetermined problems" on page 27. Notes • If you have both an error message and an incorrect audio response diagnose the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 25
failing hard disk drive. 2. Using the operating systems programs format the hard disk drive. Replace the hard disk drive. Power Supply Problems If you suspect a power problem, use the following procedures. Check/Verify FRU/Action Check the following for proper Reseat connectors installation - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 26
Manual Beep symptoms Beep symptoms are tones or a series Motherboard timer not operational problem with the system. Consult your system manufacturer. Before declaring the motherboard 8042 Gate A20 test error (cannot manufacturer's technical support. switch to protected mode) • If beep codes - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 27
problem with the system. Consult your system manufacturer. Before declaring the motherboard your system manufacturer's technical support. • If beep codes problem happens again. This will reveal the malfunctioning card. POST error codes Each time you power-on the system, it performs a series - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 28
Manual installed. PS2 Mouse support is enabled in the BIOS setup butthe device is not detected. You can plug PS2 Mouse or set PS2 Mouse support is auto. Setup to Enable. The BIOS then ignores the missing keyboard during POST. The system has been halted. A reset or power cycle is required to - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 29
in selected Boot device Description/Action The BIOS was unable to find a suitable boot . Make sure you have bootable media. Undetermined problems If this computer has a parallel ATA hard the optical drive is jumpered as a slave. 1. Power-off the computer. 2. Remove or disconnect the following - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 30
Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. Note Use only parts provided by Lenovo power cords from electrical outlets. 3. Disconnect all cables attached to the computer. This includes power - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 31
Chapter 7. Replacing hardware 5. Pull down the switch at the rear of the chassis and slide the computer cover to the rear to remove. 29 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 32
Hardware Maintenance Manual Removing and replacing the front bezel To remove and replace the front bezel: 1. Remove the computer cover. Refer to "Removing the computer cover". 2. Remove the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 33
included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace the power supply: 1. Remove the computer cover. Refer to "Removing the computer - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 34
Manual 8. Reconnect a power supply connector to each of the drives. 9. Refer to the "Completing the installation". Replacing the heat sink assembly Attention Do not remove the computer cover or attempt any repair before reading the "Important safety information" in the Safety and Warranty Guide - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 35
that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace a memory module: 1. Remove the computer cover. Refer to "Removing the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 36
was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace an adapter: 1. Remove the computer cover. Refer to "Removing the computer - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 37
Chapter 7. Replacing hardware 3. Install the new adapter into the same adapter connector. 4. Ensure the adapter is fully seated into the adapter connector. 5. At the rear of the computer, pivot the adapter latch to the closed 35 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 38
Hardware Maintenance Manual position to secure the adapter. 6. Refer to the "Completing the installation". Note: Replacement of some models equipped with graphic adapter the bracket clip the adapter. 2. Install the two screws to secure the bracket. Note: Use only the screws provided by Lenovo. 36 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 39
Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support recovering factory-installed software, refer to "OneKey Recovery" in the User Guide. To replace the hard disk drive: 1. Remove the computer cover. - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 40
that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace an optical drive 1. Remove the computer cover. Refer to "Removing the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 41
the front of the computer. 5. Slide the new optical drive into the bay from the front until it snap into position. 6. Connect the signal and power cables to the drive. 7. Install the front bezel. Refer to "Removing and replacing the front bezel". 8. Refer to the "Completing the installation". 39 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 42
was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace the system fan assembly: 1. Remove the computer cover. Refer to "Removing - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 43
that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace the keyboard: 1. Remove any media (diskettes, CDs, or tapes) from the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 44
that was included with your computer or in the Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://www.lenovo.com/support. To replace the mouse: 1. Remove any media (diskettes, CDs, or tapes) from the - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 45
cover and reconnect cables, including telephone lines and power cords. Also, depending on the part that was replaced, you might need to confirm the updated information in the Setup Utility program. Refer to "Starting the Setup Utility" in the User Guide or in the Hardware Maintenance Manual. 43 - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 46
" and "Locating connectors on the rear of the computer". 6. To update your configuration settings, refer to "Starting the Setup Utility" in the User Guide or in the Hardware Maintenance Manual. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 47
service representative might find helpful. Power management Power management reduces the power consumption of certain components of the computer such as the system power supply, processor, hard disk drives, and some monitors. Automatic configuration and power interface (ACPI) BIOS that support this - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 48
to instructions and requirements in all the manuals included with your computer, or operate the product inappropriately for reasons such as misunderstanding, Lenovo out by Lenovo professional service staff. Lenovo (Beijing) Co., Ltd. has performed strict collation for all the manuals included with - Lenovo IdeaCentre K210 | K200 Hardware Maintenance Manual - Page 49
all the manuals included with your computer. For the latest information or any questions or comments, contact or visit Lenovo website: Service website: http://www.lenovo.com Lenovo is trademarks of Lenovo (Beijing ) Co., Ltd. Microsoft is the registered trademark of Microsoft. Microsoft Windows XP
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
 |
 |
Contents
i
Contents
Chapter 1. About this manual
................................................
1
Important
Safety Information
......................................................................
1
Using eSupport
....................................................................................................
2
Important information about replacing RoHS compliant FRUs ..2
Chapter 2. Safety information
................................................
4
General safety
.......................................................................................................
4
Electrical safety
....................................................................................................
5
Safety inspection guide
...................................................................................
7
Handling electrostatic discharge-sensitive devices
.........................
8
Grounding requirements
...............................................................................
8
Safety notices
........................................................................................................
9
Chapter 3. General information
...........................................
12
Speciļ¬cations
.....................................................................................................
12
Chapter 4. General Checkout
...............................................
13
Problem determination tips
......................................................................
14
Chapter 5. Using the Setup Utility
......................................
16
Starting the Setup Utility program
.........................................................
16
Viewing and changing settings
................................................................
16
Using passwords
..............................................................................................
17
Password considerations
..................................................................................................
17
Supervisor password
..........................................................................................................
17
User Password
........................................................................................................................
18
Security Options
...................................................................................................................
19
Using Device
......................................................................................................
20
Selecting a startup device
...........................................................................
20