Lenovo S20-00 Lenovo S20-00 Hardware Maintenance Manual
Lenovo S20-00 Manual
View all Lenovo S20-00 manuals
Add to My Manuals
Save this manual to your list of manuals |
Lenovo S20-00 manual content summary:
- Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 1
Lenovo S20-00 All-In-One PC Hardware Maintenance Manual Machine Types: F0AY [S20-00] - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 2
- Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 3
Lenovo S20-00 All-In-One PC Hardware Maintenance Manual Machine Types: F0AY [S20-00] - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 4
Second Edition (September 2014)12th © Copyright Lenovo 2014, 2014. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration "GSA" contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 5
mode 17 Exiting the Lenovo BIOS Setup Utility program . . 17 Chapter 6. Symptom-to-FRU Index . . 19 Hard disk drive boot error 19 Power Supply Problems 19 POST error codes 20 Undetermined problems 20 Chapter 7. Replacing hardware . . . . 21 General information 21 Replacing the keyboard and - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 6
iv Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 7
manual This manual contains service and reference information for Lenovo S20-00 All-In-One computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo computer products. Before servicing a Lenovo this manual before following any of the instructions. Veuillez - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 8
2 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 9
the weight servicing the computer. • Keep your tool case away from areas that people may walk through to ensure no-one trips over it. • Do not wear loose clothing that can be trapped in the moving parts instructed otherwise in the installation and configuration procedures. © Copyright Lenovo 2014, - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 10
soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats : - Performing a mechanical inspection - Working near power supplies - Removing or installing Field Replaceable Units ( . 4 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 11
installed to protect users and service personnel from injury. This guide addresses only those items. can continue without first resolving the problem. Consider the following items and the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 12
device covers, unless instructed otherwise in the installation and configuration procedures. • Connect and disconnect cables as described in the following table when installing, moving, or opening covers on this product or attached devices. 6 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 13
4. Remove all cables from devices. CAUTION: When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery recommended by laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 14
one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 2 1 CAUTION: Do not place any object weighing more than 82 kg (180 lbs.) on top of rack-mounted devices. 8 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 15
all computer models covered by this manual. Specifications This section lists the physical specifications for your computer. This section lists the physical specifications for your computer. Type Lenovo S20-00 This section lists the physical specifications. Environment Air temperature: Operating: 10 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 16
10 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 17
If one of the following happens, follow the instruction given: • If the computer displays a POST error, go to "POST error codes". • If the computer hangs and no error is displayed, continue at step 7. 7. If the test stops and you cannot continue, replace the last device tested. © Copyright Lenovo - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 18
12 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 19
Setup Utility program." You must use the keyboard when using the Lenovo BIOS Setup Utility menu. The keys used to perform various tasks are displayed on the bottom of each screen. Using passwords You can use the Lenovo BIOS Setup Utility program to set passwords to prevent unauthorized persons from - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 20
, then press the Enter key. A Setup Notice will be displayed confirming that your changes have been saved. 5. Return to the Lenovo BIOS Setup Utility program menu and select the Exit option. 6. Select Save Changes and Exit from the menu. 14 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 21
to 16 characters (a-z and 0-9). To set a Power-On Password, do the following: 1. Start the Lenovo BIOS Setup Utility program (see "Starting the Lenovo BIOS Setup Utility program" on page 13). 2. From the Security menu, select Set Power-On Password and press the Enter key. 3. The password dialog box - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 22
. 3. Use ↑ and ↓ arrows to select the desired startup device from the Startup Device Menu and press the Enter key to begin. Note: Selecting a startup device from the Startup Device Menu does not permanently change the startup sequence. 16 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 23
computer, you must change the boot mode to Legacy support. The legacy Windows operating system cannot be installed if you don't change the boot mode. To change the booting mode, do the following: 1. Start the Lenovo BIOS Setup Utility program (see "Starting the Lenovo BIOS Setup Utility program" on - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 24
18 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 25
an operating system on the boot drive. The drive must be formatted. Do the following: 1. Attempt to back up the data on the failing hard disk drive. 2. Use the operating system to format the hard disk drive. Replace the hard disk drive. Power Supply Problems Follow these procedures if you suspect - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 26
re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or component. If all devices and components have been removed and the problem continues, replace the system board. 20 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 27
with your computer. To obtain copies of the Safety and Warranty Guide, go to the Support Web site at: http://support.lenovo.com. Note: Use only parts provided by Lenovo. General information Pre-disassembly instructions Before starting the disassembly procedure, make sure that you do the following - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 28
be replaced using Lenovo recommends that you use a blanket, towel, or other soft cloth to protect the touch screen from scratches or other damage. To remove the rear cover: Step 1. Step 2. Step 3. Remove any media (disks, CDs, DVDs, or memory Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 29
holes on the front bezel, and place the rear cover into position. c. Secure the rear cover to the front bezel with the two screws. Chapter 7. Replacing hardware 23 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 30
rear cover. To replace the hard disk drive: Step 1. Remove any media (disks, CDs, DVDs or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. 24 Lenovo S20-00 All-In-One PC Hardware - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 31
hard disk drive assembly to the rear cover with the four screws. d. Connect the data and power cables to the new hard disk drive. Chapter 7. Replacing hardware 25 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 32
to let it cool down before removing the rear cover. To replace the Wi-Fi card: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. 26 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 33
the computer and wait 3 to 5 minutes to let it cool down before removing the rear cover. To replace the speaker system: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 34
cool down before removing the rear cover. To replace the power switch board: Step 1. Step 2. Step 3. Step 4. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the cover. Refer to "Removing the rear cover". 28 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 35
computer and wait 3 to 5 minutes to let it cool down before removing the rear cover. To replace the motherboard: Step 1. Step 2. Step 3. Step 4. Step 5. Step 6. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 36
Step 7. Remove all the cables connected to the motherboard. 30 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 37
holes on the motherboard with the mounting holes on the rear cover and secure the motherboard with the eight screws. c. Attach the Wi-Fi card, memory modules to the motherboard. d. Connect all the cables to the motherboard. Step 11. Reattach the rear cover and secure it with the screws. Chapter - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 38
cover. To replace the converter board: Step 1. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached devices. Step 2. Unplug all power cords from electrical outlets. 32 Lenovo S20-00 All-In-One PC Hardware - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 39
computer and wait 3 to 5 minutes to let it cool down before removing the rear cover. To replace the LED panel: Step 1. Step 2. Step 3. Step 4. Step 5. Remove any media (disks, CDs, DVDs, or memory cards) from the drives, shut down the operating system, and turn off the computer and all attached - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 40
Step 6. Remove the two screws that secure the converter bracket to the front bezel. Lift up the bracket to remove it. 34 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 41
. Step 9. Press the pin to unlock the converter cable from the connector on the LED panel, then pull the converter cable out as shown. Chapter 7. Replacing hardware 35 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 42
11. Remove the four screws, and then remove the supporting brackets from the panel. Step 12. To install the new the LED panel: a. Attach the supporting brackets to the new panel with the four screws. rear cover and secure it with the screws. 36 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 43
the field replaceable units (FRUs) for Lenovo S20-20 All-In-One desktop computers. Attention: Be sure to read and understand all the safety information before replacing any FRUs. Notes: FRUs that have a 1 or 2 in the CRU column are Customer Replaceable Units (CRUs). • 1- identifies parts that are - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 44
S2000 W8S J1800 1G DIS MB 5B20G56352 RAM 2 M471B5674QH0YK0 2GB D3L1600S Memory HF 1100983 HMT425S6AFR6APB 2GB D3L1600S Memory HF 1100643 MT4KTF25664HZ1G6E1 2GB D3L1600S Memory 1100956 Mic_R D9PSH 2GB D3L1600S Memory 4K 16200513 38 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 45
36200352 Liteon PA165072IA 65W adapter 36200353 DELTA ADP90XD BC 90W common adapter ® 36200415 Liteon PA190072IA 90w common adapter® 36200416 C Board S2000 Power 5C50G56338 Wifi N Liteon WB335 1x1BGN+BT4.0 HMC WLAN 20200437 CBT RTL8723BE 1x1BN+BT4.0 PCIE HMC 20200440 Camera N AVC - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 46
Cable_AUO 90205346 C260 Converter Board to Panel Cable_LG 90205345 C Antenna S2000 Main+AUX 5A30G56383 SPEAKERINT N SPEAKERINT C S2000 L+R 5SB0G10727 KB&MS 1 LTO SK8821(S PKG)(CN-EN) Ultraslim plus wireless KB+MC LC8 25210791 40 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 47
Primax Edge 2.4G KB+MC(EN) CALC8 Primax Edge 2.4G KB+MC(IN) CALC8 Primax Edge 2.4G KB+MC(RU) CALC8 Primax Edge 2.4G KB+MC(UK) CALC8 Primax Edge 2.4G KB+MC(TR) CALC8 Primax Edge 2.4G KB+MC(CZ) CALC8 Primax Edge 2.4G KB+MC(TH) CALC8 Primax Edge 2.4G KB+MC(SA) CALC8 Primax Edge 2.4G KB+MC(LA) CALC8 - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 48
31503362 HLS1MC5 Israel Power cord 31049502 LW Black single head1.0m Taiwan C5 Power cord® 31038885 LX(BS)1.0M C5 TW Power cord 31503354 42 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 49
HLS1MC5 TW Power cord LW Black single head1.0m Korea C5 Power cord® LX(BS)1.0M C5 Korea Power cord HLS1MC5 Korea Power cord LW Black single head1.0m SA C5 Power cord® LX(BS)1.0M C5 SA Power cord HLS1MC5 SA Power cord 31049499 31039106 31503358 31049498 31039105 31503355 31049501 Chapter 8. FRU - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 50
44 Lenovo S20-00 All-In-One PC Hardware Maintenance Manual - Lenovo S20-00 | Lenovo S20-00 Hardware Maintenance Manual - Page 51
of the computer and the settings for Advanced Power Management (APM) BIOS mode is ignored. Not all operating systems support ACPI BIOS mode. Automatic Power-On features The Automatic Power-On features within the Power Management menu allow you to enable and disable features that turn on the computer
Lenovo S20-00 All-In-One PC Hardware
Maintenance Manual
Machine Types: F0AY [S20-00]