Home » Lenovo Manuals » Servers » Lenovo ThinkServer TD200 » Manual Viewer

Lenovo ThinkServer TD200 (English) Installation and User Guide - Page 136

Removing an optional ServeRAID-MR10is VAULT SAS/SATA controller, Attention, Important

View all Lenovo ThinkServer TD200 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

1 Power supply support bracket 2 Power supply release tab 19. If you have other options to install or remove, do so now. 20. Replace the side cover (see "Installing the side cover" on page 134). Go to "Completing the installation" on page 130. If you have other options to install or remove, do so now. Otherwise, go to "Completing the installation" on page 130. Removing an optional ServeRAID-MR10is VAULT SAS/SATA controller To remove a ServeRAID-MR10is SAS/SATA adapter, do the following: 1. Read the safety information (see "Safety" on page vii and "Installation guidelines" on page 37). 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. Remove the side cover (see "Removing the side cover" on page 43. 3. Carefully position the server on its side so that it is lying flat and facing up. Note: Do not allow the server to fall over. 4. Rotate the rear adapter-retention bracket to the open (unlocked) position. 5. Disconnect any cables connected to the adapter. Attention: To avoid breaking the retaining clips or damaging the ServeRAID-MR10is adapter connector, open and close the clips gently. 6. Carefully open the retaining clip on each end of the ServeRAID-MR10is adapter connector and remove the adapter from the server. 7. If you are instructed to return the adapter, follow all packaging instructions, and use any packaging materials that are supplied to you for shipping. Installing the optional ServeRAID-MR10is VAULT SAS/SATA controller The optional ServeRAID-MR10is VAULT SAS/SATA controller can be installed only in its dedicated connector, PCI slot 1, on the system board. The ServeRAID-MR10is adapter is supported on hot-swap server models only. The ServeRAID-MR10is SAS/SATA adapter with an encryption 1078 DE chip set enables integrated RAID levels 0, 1, 5, 6, 10, 50, and 60 support capability on hot-swap hard disk drives. For configuration information, see the documentation on the ServeRAID CD that comes with the adapter. Important: To ensure that any of your ServeRAID 10i, 10is, or 10M adapters function properly on UEFI-based servers, make sure that the adapter firmware level is updated to at least 11.xx-XXX, and the supporting drivers. Attention: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. To install the ServeRAID-MR10is SAS/SATA controller and route the cables, do the following: 1. Read the safety information (see "Safety" on page vii and "Installation guidelines" on page 37). 118 ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide

Section	Page
Contents	5
Safety	9
Chapter 1. Introduction	19
Notices and statements in this document	20
Related documentation	21
Chapter 2. Server setup roadmap	23
Chapter 3. What is included with your server	25
Features and technologies	25
Specifications	27
Software	30
EasyStartup	30
EasyManage	30
Reliability, availability, and serviceability	31
Chapter 4. Server controls, LEDs, and power	33
Front view	33
Operator information panel	37
EasyLED diagnostic panel	38
Rear view	44
System-board internal connectors	46
System-board external connectors	47
System-board option connectors	48
System-board switches and jumpers	49
System-board LEDs	51
Optional one-slot PCI extender card	52
Optional two-slot PCI extender card	52
Server power features	53
Turning on the server	53
Turning off the server	53
Chapter 5. Installing optional devices and replacing customer replaceable units	55
Installation guidelines	55
System reliability guidelines	56
Working inside the server with the power on	56
Handling static-sensitive devices	57
Major components of the server	58
Opening the bezel	58
Opening and closing the bezel media door	60
Removing the side cover	61
Removing the air baffle	62
Removing the fan cage assembly	64
Installing the fan cage assembly	65
Removing the front USB connector assembly	67
Installing the front USB connector assembly	69
Removing the rear adapter-retention bracket	70
Installing the rear adapter retention bracket	71
Removing the front adapter-retention bracket	72
Installing the front adapter-retention bracket	72
Removing the battery	72
Installing the battery	73
Removing and installing drives	75
Removing a DVD drive	77
Installing a DVD drive	80
Removing an optional tape drive	84
Installing an optional tape drive	85
Removing a 2.5-inch hot-swap hard disk drive	88
Installing a 2.5-inch hot-swap hard disk drive	89
Removing a 3.5-inch hot-swap hard disk drive	91
Installing a 3.5-inch hot-swap hard disk drive	92
Removing a simple-swap hard disk drive	93
Installing a simple-swap hard disk drive	94
IDs for hot-swap hard disk drives	95
Power and signal cables for internal drives	96
Removing a power supply	97
Installing a power supply	100
Removing a hot-swap fan	102
Installing a hot-swap fan	103
Removing a memory module	104
Installing a memory module	107
Removing an adapter	113
Installing an adapter	114
Installing a second microprocessor	117
Removing a ServeRAID-BR10i SAS/SATA controller	123
Installing the ServeRAID-BR10i SAS/SATA controller	124
Removing an optional ServeRAID-MR10i SAS/SATA controller	129
Installing the optional ServeRAID-MR10i SAS/SATA controller	130
Removing an optional ServeRAID-MR10is VAULT SAS/SATA controller	136
Installing the optional ServeRAID-MR10is VAULT SAS/SATA controller	136
Removing the virtual media key	143
Installing the virtual media key	144
Removing the control-panel assembly	145
Installing the control-panel assembly	147
Completing the installation	148
Closing the bezel	148
Installing the air baffle	150
Installing the side cover	152
Connecting the cables	152
Updating the server configuration	153
Connecting external devices	154
Chapter 6. Configuring the server	155
Using the Setup Utility	156
Starting the Setup Utility	156
Setup Utility menu choices	156
Passwords	159
Power-on password	160
Administrator password	160
Configuring RAID controllers	160
Using the LSI Configuration Utility program	161
Starting the LSI Configuration Utility program	162
Formatting a hard disk drive	162
Creating a RAID array of hard disk drives	162
Using the WebBIOS utility	163
Starting the WebBIOS utility	163
Main menu of the WebBIOS utility	163
Creating a storage configuration using the Configuration Wizard	164
Viewing and changing properties	164
Viewing and changing virtual disk properties	164
Using the EasyStartup DVD	165
Before you use the EasyStartup DVD	165
Configuring RAID	166
EasyStartup overview	166
Setup and configuration	166
Typical operating-system installation	167
Installing your operating system without using EasyStartup	168
Using the Boot Manager program	168
Enabling the Broadcom Gigabit Ethernet Utility program	169
Configuring the Broadcom Gigabit Ethernet controller	169
Updating the firmware	169
Starting the backup server firmware	170
Recovering the server firmware	170
Automated boot recovery (ABR)	172
Three boot failure	172
Using the integrated management module	173
Using the remote presence capability and blue-screen capture	174
Enabling the remote presence feature	174
Obtaining the IP address for the IMM	175
Logging on to the Web interface	175
Diagnostics programs and messages	176
Running the diagnostics programs	176
Advanced Settings Utility program	177
Installing EasyManage software	178
Installation requirements	178
Installation order	178
Installing Windows 2003 components on the Core Server	179
Installing Windows 2008 32-bit components	179
Installing Web Server Role (IIS)	179
Installing Microsoft SNMP services	180
Uninstalling the LANDesk Software Agent	180
Chapter 7. Troubleshooting	181
Troubleshooting tables	181
CD or DVD drive problems	181
Diskette drive problems	182
General problems	183
Hard disk drive problems	183
Intermittent problems	184
Keyboard, mouse, or pointing-device problems	184
Memory problems	185
Microprocessor problems	186
Monitor or video problems	186
Optional-device problems	188
Power problems	189
Serial port problems	190
Software problems	191
Universal Serial Bus (USB) port problems	191
Solving undetermined problems	191
Solving SCSI problems	192
Solving power problems	193
Solving Ethernet controller problems	193
POST	194
Event logs	194
Viewing event logs from the Setup Utility	195
Viewing event logs without restarting the server	195
Clearing the event logs	196
POST error codes	196
Appendix A. Getting help and technical assistance	205
Before you call	205
Using the documentation	205
Getting help and information from the World Wide Web	205
Calling for service	206
Using other services	206
Purchasing additional services	207
Lenovo product service	207
Appendix B. Notices	209
Trademarks	210
Important notes	210
Product recycling and disposal	211
Compliance with Republic of Turkey Directive on the Restriction of Hazardous Substances	212
Recycling statements for Japan	213
Battery return program	213
German Ordinance for Work gloss statement	214
Electronic emission notices	215
Federal Communications Commission (FCC) statement	215
Industry Canada Class A emission compliance statement	215
Avis de conformité à la réglementation d′Industrie Canada	215
Australia and New Zealand Class A statement	215
United Kingdom telecommunications safety requirement	215
European Union EMC Directive conformance statement	215
Germany Class A compliance statement	216
Japanese Voluntary Control Council for Interference (VCCI) statement	217
Taiwan Class A warning statement	217
People's Republic of China Class A warning statement	217
Korea Class A warning statement	218
Index	219
A	219
B	219
C	219
D	220
E	220
F	220
G	221
H	221
I	221
J	221
K	221
L	221
M	222
N	222
O	222
P	222
R	223
S	223
T	224
U	225
V	225

Match case Limit results 1 per page

±1²

Power supply support bracket

±2²

Power supply release tab

19.

If you have other options to install or remove, do so now.

20.

Replace the side cover (see “Installing the side cover” on page 134). Go to

“Completing the installation” on page 130.

If you have other options to install or remove, do so now. Otherwise, go to

“Completing the installation” on page 130.

Removing an optional ServeRAID-MR10is VAULT SAS/SATAcontroller

To remove a ServeRAID-MR10is SAS/SATAadapter, do the following:

Read the safety information (see “Safety” on page vii and “Installation

guidelines” on page 37).

Turn off the server and peripheral devices, and disconnect the power cords and

all external cables. Remove the side cover (see “Removing the side cover” on

page 43.

Carefully position the server on its side so that it is lying flat and facing up.

Note:

Do not allow the server to fall over.

Rotate the rear adapter-retention bracket to the open (unlocked) position.

Disconnect any cables connected to the adapter.

Attention:

To avoid breaking the retaining clips or damaging the

ServeRAID-MR10is adapter connector, open and close the clips gently.

Carefully open the retaining clip on each end of the ServeRAID-MR10is adapter

connector and remove the adapter from the server.

If you are instructed to return the adapter, follow all packaging instructions, and

use any packaging materials that are supplied to you for shipping.

Installing the optional ServeRAID-MR10is VAULT SAS/SATAcontroller

The optional ServeRAID-MR10is VAULT SAS/SATAcontroller can be installed only

in its dedicated connector, PCI slot 1, on the system board. The ServeRAID-MR10is

adapter is supported on hot-swap server models only. The ServeRAID-MR10is

SAS/SATA adapter with an encryption 1078 DE chip set enables integrated RAID

levels 0, 1, 5, 6, 10, 50, and 60 support capability on hot-swap hard disk drives. For

configuration information, see the documentation on the ServeRAID CD that comes

with the adapter.

Important:

To ensure that any of your ServeRAID 10i, 10is, or 10M adapters

function properly on UEFI-based servers, make sure that the adapter firmware level

is updated to at least 11.xx-XXX, and the supporting drivers.

Attention:

Some cluster solutions require specific code levels or coordinated code

updates. If the device is part of a cluster solution, verify that the latest level of code

is supported for the cluster solution before you update the code.

To install the ServeRAID-MR10is SAS/SATAcontroller and route the cables, do the

following:

Read the safety information (see “Safety” on page vii and “Installation

guidelines” on page 37).

118

ThinkServer TD200 Types 3724, 3808, 3809, 3815, 3817, 3824, 3826, 3836: Installation and User Guide