LevelOne FCS-5044 Manual - Page 28

Port parameters setting

Get LevelOne FCS-5044 PDF manuals and user guides View all LevelOne FCS-5044 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Network Camera User's Manual "LAN" & "PPPoE" The default type is LAN. Select PPPoE if using ADSL 1. LAN The default status is Get IP address automatically. This could be tedious to perform software installation whenever the Network Camera starts. Therefore, once the network is set, especially for the IP address should be entered correctly. Select Use fixed IP address then the Network Camera will skip installation. The Network Camera will automatically restart and operate normally after a power outage. You can run IP installer to check the IP address assigned to the Network Camera if the IP address is forgotten, or you can use the UPnP function provided by the Network Camera (MS Windows XP provides UPnP function at My Network Place). (1) "Get IP address automatically" (2) "Use fixed IP address" - "IP address": This is necessary for network identification. - "Subnet mask": This is used to determine if the destination is in the same subnet. The default value is ―255.255.255.0‖. - "Default router": This is a gateway used to forward frames to destinations in a different subnet. Invalid router setting will fail the transmission to destinations in different subnet. - "Primary DNS": The primary domain name server that translates hostnames into IP addresses. - "Secondary DNS": Secondary domain name server backups the Primary DNS. 2. PPPoE If using the PPPoE interface, you should fill the following settings from ISP. (1) "User name": The login name of PPPoE account (2) "Password": The password of PPPoE account (3) "Confirm password": Input password again for confirmation Port parameters setting Advanced Mode - "Http Port" This can be typed besides the default Port 80. Once the port is changed, the users must make sure the change for the connection is successful. For instance, when the Administrator changes the HTTP port of the Network Camera which IP address is 192.168.0.20 from 80 or 1025 to 65535, the users must type in the web browser ―http://192.168.0.20:8080‖ instead of ―http://192.168.0.20‖. - "Https Port" By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025 and 65535. - "RTSP Port" RTSP port can be typed besides the default Port 554. - "Video RTP Port" Video RTP port can be typed besides the default Port 6790. 28/63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
Network Camera User
’
s Manual
28/63
“
LAN
”
&
“
PPPoE
”
The default type is LAN. Select PPPoE if using ADSL
1. LAN
The default status is
Get IP address automatically
. This could be tedious to perform
software installation whenever the Network Camera starts. Therefore, once the network
is set, especially for the IP address should be entered correctly. Select
Use fixed IP
address
then the Network Camera will skip installation. The Network Camera will
automatically restart and operate normally after a power outage. You can run IP installer
to check the IP address assigned to the Network Camera if the IP address is forgotten,
or you can use the UPnP function provided by the Network Camera
(MS Windows XP
provides UPnP function at My Network Place)
.
(1) “Get IP address automatically”
(2) “Use fixed IP address”
-
“IP address”
:
This is necessary for network identification.
-
“Subnet mask”
:
This is used to determine if the destination is in the same
subnet. The default value is ―255.255.255.0‖.
-
“Default router”
:
This is a gateway used to forward frames to destinations in a
different subnet. Invalid router setting will fail the transmission to destinations in
different subnet.
-
“Primary DNS”
:
The primary domain name server that translates hostnames
into IP addresses.
-
“Secondary DNS”
:
Secondary domain name server backups the Primary DNS.
2. PPPoE
If using the PPPoE interface, you should fill the following settings from ISP.
(1) “User name”:
The login name of PPPoE account
(2) “Password”:
The password of PPPoE account
(3) “Confirm password”:
Input password again for confirmation
Port parameters setting
Advanced Mode
-
“Ht
tp P
ort”
This can be typed besides the default Port 80. Once the port is changed,
the users must make sure the change for the connection is successful. For instance,
when the Administrator changes the HTTP port of the Network Camera which IP
address is 192.168.0.20 from 80 or 1025 to 65535, the users must type in the web
-
“Http
s P
ort”
By default, the HTTPS port is set to 443. It can also be assigned to
another port number between 1025 and 65535.
-
“RTSP Port”
RTSP port can be typed besides the default Port 554.
-
“
Video RTP
Port”
Video RTP port can be typed besides the default Port 6790.