LevelOne IES-1880 Quick Install Guide - Page 2
Power Input, Console Configuration, Web Configuration
View all LevelOne IES-1880 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Power Input Power1 Power2 + 12 to 48VDC - Power Ground + 12 to 48VDC - Power Ground Terminal Block Earth Ground Relay Output 1A @ 24VDC 1. The relay contact closes if Power1 or Power2 are both failed 2. The relay contact closes if Power3 is failed but both Power1 and Power2 are On Power3: DC Jack type with 12VDC Input WARNING - EXPLOSION HAZARD - Do not disconnect equipment while the circuit is live or unless the area is known to be free of ignitable concentrations. WARNIN G - EXPLOSION HAZARD - Substitution of any component may impair suitabili ty for Class I, Division 2. WARNIN G - Exposure to some chemicals may degrade the sealing properties of materials used in the Sealed Relay Device. RECOMMENDATION - It is recommended to inspect the sealed relay device periodically and to check for any degradation of the materials and to replace the complete product, not the sealed device, if any degradation is found. IES-1880 Page 4 Terminal Mode). And the "switch_a(config)#" prompt will show on the screen. 12. Set new IP address and subnet mask for Switch: 13. At the "switch_a(config)#" prompt just type in "interface vlan1.1" and press to logon to vlan 1 (vlan1.1 means vlan 1). And the "switch_a(config-if)#" prompt will show on the screen. 14. Command Syntax: "ip address A.B.C.D/M". "A.B.C.D" specifies IP address. "M" specifies IP subnet mask. "M"= 8: 255.0.0.0, 16:255.255.0.0, or 24: 255.255.255.0. 15. For example, At the "switch_a(config-if)#" prompt just type in "ip address 192.168.1.10/24" and press to set new IP address (192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch Console Configuration 1. Connect to the switch console: 2. Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of the terminal or computer running the terminal emulation application. Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal) to the switch console port. 3. Configuration settings of the terminal-emulation program: 4. Baud rate: 115,200bps, Data bits: 8, Parity: none, Stop bit: 1, Flow control: none. 5. Press the "Enter" key. The Command Line Interface (CLI) screen should appear as below: 6. Logon to Exec Mode (View Mode): 7. At the "switch_a login:" prompt just type in "root" and press to logon to Exec Mode (or View Mode). And the "switch_a>" prompt will show on the screen. 8. Logon to Privileged Exec Mode (Enable Mode): 9. At the "switch_a>" prompt just type in "enable" and press to logon to Privileged Exec Mode (or Enable Mode). And the "switch_a#" prompt will show on the screen. 10. Logon to Configure Mode (Configure Terminal Mode): 11. At the "switch_a#" prompt just type in "configure terminal" and press to logon to Configure Mode (or Configure IES-1880 Page 5 Web Configuration 1. Login the switch: 2. Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be shown as below: 3. Enter the factory default login ID: root. 4. Enter the factory default password (no password). 5. Then click on the "Login" button to log on to the switch. IES-1880 Page 6 Note: Please refer to User Manual for more detailed information IES-1880 Page 7