LevelOne PLI-2040 Quick Install Guide - Page 3

HomePlug On, Flashing, Ethernet, Setup, Microsoft .NET Framework 1.1, Microsoft .NET, Framework 1.1

Get LevelOne PLI-2040 PDF manuals and user guides View all LevelOne PLI-2040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

HomePlug On - The Powerline network is active. This means that at least one other HomePlug device was detected. Off - Powerline network is not available - no other HomePlug devices were detected. Flashing - Data is being transmitted or received via the Powerline network. Ethernet On - Ethernet connection is active. Off - No Ethernet connection. Flashing - Data is being transmitted or received via the Ethernet Port. Setup Configuration requires the use of Windows PC. Once configured, any device may be connected to the 200Mbps HomePlug AV Adapter's Ethernet port. To perform configuration, follow the procedures list below. 1. Connect a standard LAN cable from the 200Mbps HomePlug AV Adapter's Ethernet port to your PC. 2. Plug the 200Mbps HomePlug AV Adapter into a power outlet. 3. Wait a few seconds for startup to be completed, and then check the LEDs  The Power LED should be ON.  The HomePlug LED will be ON if other HomePlug devices are detected, otherwise it will be OFF.  The Ethernet LED should be ON. 4. Insert the supplied CD-ROM into your Windows PC, and wait for it to start, select "Utility" from the autorun screen. If it does not start automatically, locate and run SETUP.EXE. 5. Follow the prompts to install the PLI-2040 utility. 6. Microsoft .NET Framework 1.1 is needed for installing PLI-2040 utility. The wizard will check automatically whether the Microsoft .NET Framework 1.1 was installed on your PC or not. If not, the wizard will pop up a message box. Click OK to install Microsoft .NET Framework 1.1 first. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
3
HomePlug On
- The Powerline network is active. This means that at least one other
HomePlug device was detected.
Off
- Powerline network is not available - no other HomePlug devices were
detected.
Flashing
- Data is being transmitted or received via the Powerline network.
Ethernet
On
- Ethernet connection is active.
Off
- No Ethernet connection.
Flashing
- Data is being transmitted or received via the Ethernet Port.
Setup
Configuration requires the use of Windows PC. Once configured, any device may be connected
to the 200Mbps HomePlug AV Adapter's Ethernet port. To perform configuration, follow the
procedures list below.
1. Connect a standard LAN cable from the 200Mbps HomePlug AV Adapter's Ethernet port to
your PC.
2. Plug the 200Mbps HomePlug AV Adapter into a power outlet.
3. Wait a few seconds for startup to be completed, and then check the LEDs
The
Power
LED should be ON.
The
HomePlug
LED will be ON if other HomePlug devices are detected, otherwise it will
be OFF.
The
Ethernet
LED should be ON.
4. Insert the supplied CD-ROM into your Windows PC, and wait for it to start, select
“
Utility
”
from the autorun screen. If it does not start automatically, locate and run SETUP.EXE.
5. Follow the prompts to install the
PLI-2040
utility.
6.
Microsoft .NET Framework 1.1
is needed for installing
PLI-2040
utility. The wizard will
check automatically whether the
Microsoft .NET Framework 1.1
was installed on your PC
or not. If not, the wizard will pop up a message box. Click
OK
to install
Microsoft .NET
Framework 1.1
first
.