LevelOne WAB-5120 Manual - Page 38

Maximum Output Power per chain, Data Rate, Extension Channel Protection Mode, Enable MAC Clone

Get LevelOne WAB-5120 PDF manuals and user guides View all LevelOne WAB-5120 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Maximum Output Power (per chain): Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. Note: The output power here is counted from the RF single chain only not including the 16dBi internal antenna. The maximum output power will vary depending on the country selected in order to comply with the local regulation. You are able to choose "SMA Connector" only when you have well done installing the external antenna; otherwise, it might damage the unit itself. Data Rate Usually "Auto" is preferred. Under this rate, the Wireless Outdoor CPE will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. Extension Channel Protection Mode This is to avoid conflict with other wireless network and boost the ability of your device to catch all legacy devices transmissions. However, it may decrease wireless network performance. Compared to CTS-Self; the transmission amount of CTS-RTS is much lower. Enable MAC Clone Available in wireless client mode, it hides the MAC address of the CPE while displays the one of associated wireless client or the MAC address designated manually.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Maximum Output Power (per chain):
Specify the signal transmission power. The higher the output power is, the wider the signal can
cover, but the power consumption will be greater accordingly.
The output power here is counted from the RF single chain only not including the 16dBi
internal antenna.
The maximum output power will vary depending on the country selected in order to
comply with the local regulation.
You are able to choose
“
SMA Connector
”
only when you have well done installing the
external antenna; otherwise, it might damage the unit itself.
Data Rate
Usually
“
Auto
”
is preferred. Under this rate, the Wireless Outdoor CPE will automatically select
the highest available rate to transmit. In some cases, however, like where there is no great
demand for speed, you can have a relatively-low transmit rate for compromise of a long distance.
Extension Channel Protection Mode
This is to avoid conflict with other wireless network and boost the ability of your device to catch all
legacy devices transmissions. However, it may decrease wireless network performance.
Compared to CTS-Self; the transmission amount of CTS-RTS is much lower.
Enable MAC Clone
Available in wireless client mode, it hides the MAC address of the CPE while displays the one of
associated wireless client or the MAC address designated manually.
Note: