LevelOne WAP-6115 User Manual - Page 9

Preparing for Installation, Items Required for Installation, Installing the Device

Get LevelOne WAP-6115 PDF manuals and user guides View all LevelOne WAP-6115 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

2.2 Preparing for Installation 1） Make sure that there is proper heat dissipation and adequate ventilation around the Device. 2） Position the Device out of direct sunlight and away from sources of heat and ignition. 3） Position the Device away from sources of electrical noise, such as high power radio transmitters, radar stations, and so on. 2.3 Items Required for Installation 1) Preparation of related devices: （1） Broadband Internet connection （2） PoE PSE (Power Sourcing Equipment) device like PoE switch （3） PC with an Ethernet card and TCP/IP installed 2）Phillips screwdriver, crimping tool like crimping plier, etc. 2.4 Installing the Device Before you install the Device, make sure your Internet connection and PSE device are working properly. Follow these steps to install the Device: 1) Use your crimping tool to crimp a network cable and a telephone line to the corresponding wiring port on the Device. Make sure crimp the wires in the right order. 2) Mount the Device on a wall. 3) Connect the other end of the cable that you just crimped to a PoE PSE device (like PoE switch). As a PD (Powered Device), the Device will communicate with and receive power from the PSE via the cable. 4) Configure the Device: Connect your computer to the Device either via an Ethernet cable or wirelessly), and then configure the Device through its own Web interface. The Device in Fit AP mode can also be managed by a WAC-1000/ WAC-1001 5) Connect client devices: Connect each computer or other device in your network to the Device, via an Ethernet cable or wirelessly. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
8
2.2
Preparing for Installation
1
）
Make sure that there is proper heat dissipation and adequate ventilation around the Device.
2
）
Position the Device out of direct sunlight and away from sources of heat and ignition.
3
）
Position the Device away from sources of electrical noise, such as high power radio
transmitters, radar stations, and so on.
2.3
Items Required for Installation
1) Preparation of related devices:
（
1
）
Broadband Internet connection
（
2
）
PoE PSE (Power Sourcing Equipment) device like PoE switch
（
3
）
PC with an Ethernet card and TCP/IP installed
2
）
Phillips screwdriver, crimping tool like crimping plier, etc.
2.4
Installing the Device
Before you install the Device, make sure your Internet connection and PSE device are working
properly.
Follow these steps to install the Device:
1)
Use your crimping tool to crimp a network cable and a telephone line to the corresponding
wiring port on the Device. Make sure crimp the wires in the right order.
2)
Mount the Device on a wall.
3)
Connect the other end of the cable that you just crimped to a PoE PSE device (like PoE
switch). As a PD (Powered Device), the Device will communicate with and receive power
from the PSE via the cable.
4)
Configure the Device:
Connect your computer to the Device either via an Ethernet cable or
wirelessly), and then configure the Device through its own Web interface. The Device in Fit
AP mode can also be managed by a WAC-1000/ WAC-1001
5)
Connect client devices: Connect each computer or other device in your network to the
Device, via an Ethernet cable or wirelessly.