LevelOne WBR-6804 Manual - Page 61

Troubleshooting, Why can't I con the router even the cable is

Get LevelOne WBR-6804 PDF manuals and user guides View all LevelOne WBR-6804 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Chapter 4 . Troubleshooting This Chapter provides solutions to problems for the installation and operation of the WiFi Combo Router. You can refer to the following if you are having problems. 1 Why can't I configure the router even the cable is plugged and the LED is lit? Do a Ping test to make sure that the WiFi Combo Note: It is recommended that you use Router is responding. an Ethernet connection to configure it. Go to Start > Run. 1. Type cmd. 2. Press OK. 3. Type ipconfig to get the IP of default gateway. 4. Type "ping 192.168.1.1". Assure that you ping the correct IP Address assigned to the WiFi Combo Router. It will show four replies if you ping correctly. Ensure that your Ethernet Adapter is working, and that all network drivers are installed properly. Network adapter names will vary depending on your specific adapter. The installation steps listed below are applicable for all network adapters. 1. Go to Start > Right click on "My Computer" > Properties. 2. Select the Hardware Tab. 3. Click Device Manager. 4. Double-click on "Network Adapters". 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
61
Chapter 4 . Troubleshooting
This Chapter provides solutions to problems for the installation and operation of the WiFi Combo
Router. You can refer to the following if you are having problems.
1 Why can’t I configure the router even the cable is
plugged and the LED is lit?
Do a
Ping test
to make sure that the WiFi Combo
Note:
It is recommended that you use
Router is responding.
an Ethernet connection to configure it.
Go to
Start > Run
.
1.
Type
cmd
.
2.
Press
OK.
3.
Type
ipconfig
to get the IP of default gateway.
4.
Type “
ping 192.168.1.1”.
Assure that you ping the correct IP Address assigned to
the WiFi Combo Router. It will show four replies if you ping correctly.
Ensure that your Ethernet Adapter is working, and that all network drivers are installed
properly. Network adapter names will vary depending on your specific adapter. The
installation steps listed below are applicable for all network adapters.
1.
Go to
Start > Right click on “My Computer” > Properties
.
2.
Select
the
Hardware Tab
.
3.
Click
Device Manager
.
4.
Double-click on “
Network Adapters”
.