Lexmark 16C0000 User's Guide - Page 12

Installing drivers for local printing, Setting parameters in the printer, Reports, Menu Settings

Get Lexmark 16C0000 - X 520 MFP B/W Laser PDF manuals and user guides View all Lexmark 16C0000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Installing drivers for local printing Before printing, establishing communication between the printer and computer is required. To do this: 1 Set serial parameters in the printer. 2 Install a printer driver on the attached computer. 3 Match the serial settings in the COM port. Setting parameters in the printer 1 Press on the operator panel. 2 Press until Reports appears, and then press . Note: For information about serial menus and messages, see the publications CD that shipped with the printer. 3 Press until Menu Settings Page appears, and then press . The printer returns to Ready. 4 Press . 5 Press until Network/Ports appears, and then press . 6 Press port.) until Serial or Serial [x] appears, and then press . ([x] is the number of the serial 7 Press until appears, and then press a change). (where is the parameter required for 8 Press until appears, and then press change). (where is the setting required for a Note the following restrictions: • Maximum baud rate supported is 115,200. • Data Bits must be set to 7 or 8. • Parity must be set to Even, Odd, or None. • Stop Bits must be set to 2. • Flow Control recommended protocol setting is Xon/Xoff. 9 Press to select the setting. The printer returns to Serial or Serial [x]. 10 Print a Menu Settings page, and verify that the serial parameters are correct. Note: Keep this page for later use. a Press on the operator panel. b Press until Reports appears, and then press . c Press until Menu Settings Page appears, and then press . d Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the serial parameters. Windows 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Windows
12
Installing drivers for local printing
Before printing, establishing communication between the printer and computer is required. To do this:
1
Set serial parameters in the printer.
2
Install a printer driver on the attached computer.
3
Match the serial settings in the COM port.
Setting parameters in the printer
1
Press
on the operator panel.
2
Press
until
Reports
appears, and then press
.
Note:
For information about serial menus and messages, see the publications CD that shipped with the
printer.
3
Press
until
Menu Settings Page
appears, and then press
.
The printer returns to
Ready
.
4
Press
.
5
Press
until
Network/Ports
appears, and then press
.
6
Press
until
Serial
or
Serial [x]
appears, and then press
. (
[x]
is the number of the serial
port.)
7
Press
until
<Parameter>
appears, and then press
(where
<Parameter>
is the parameter required for
a change).
8
Press
until
<Setting>
appears, and then press
(where
<Setting>
is the setting required for a
change).
Note the following restrictions:
•
Maximum baud rate supported is 115,200.
•
Data Bits must be set to 7 or 8.
•
Parity must be set to Even, Odd, or None.
•
Stop Bits must be set to 2.
•
Flow Control recommended protocol setting is Xon/Xoff.
9
Press
to select the setting. The printer returns to
Serial
or
Serial [x]
.
10
Print a Menu Settings page, and verify that the serial parameters are correct.
Note:
Keep this page for later use.
a
Press
on the operator panel.
b
Press
until
Reports
appears, and then press
.
c
Press
until
Menu Settings Page
appears, and then press
.
d
Look under the Standard Serial (or Serial Option X if a serial interface card is installed) heading to find the
serial parameters.