Lexmark MS810n Embedded Web Server-Security: Administrator's Guide - Page 37

Notes, Settings, Security, Disk Encryption, Disable, Enable, Warning-Potential Damage, Submit, Refresh

Get Lexmark MS810n PDF manuals and user guides View all Lexmark MS810n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Using security features in the Embedded Web Server 37 Notes: • View the printer IP address on the printer home screen. The IP address appears as four sets of numbers separated by periods, such as 123.123.123.123. • If you are using a proxy server, then temporarily disable it to load the Web page correctly. 2 Click Settings > Security > Disk Encryption. Note: Disk Encryption appears in the Security Menu only when a formatted, non‑defective printer hard disk is installed. 3 From the Disk Encryption menu, select either of the following: • Disable-Use this to disable disk encryption. • Enable-Use this to enable disk encryption. Notes: - Disable is the factory default setting. - Changing this setting will cause the printer to undergo a power‑on reset. Warning-Potential Damage: Changing the setting for disk encryption will erase the contents of the hard disk. 4 Click Submit to proceed with disk wiping and encryption. Note: Encryption takes approximately two minutes. Warning-Potential Damage: Do not turn off the printer during the encryption process. 5 Click Refresh to return to the Embedded Web Server. Using the printer control panel 1 Turn off the printer. 2 Hold down 2 and 6 while turning the printer on. Release the buttons only when the screen with the progress bar appears. The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully turned on, a list of functions appears on the printer display. 3 Touch Disk Encryption > Enable. 4 Touch Yes to proceed with disk encryption. Notes: • Do not turn off the printer during the encryption process. Doing so may result in loss of data. • Encryption takes approximately two minutes. • A status bar will indicate the progress of the disk wiping task. After the disk has been encrypted, the printer will return to the Enable/Disable screen. 5 Touch Back > Exit Config Menu. The printer will perform a power‑on reset, and then return to normal operating mode.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Notes:
•
View the printer IP address on the printer home screen. The IP address appears as four sets of numbers
separated by periods, such as 123.123.123.123.
•
If you are using a proxy server, then temporarily disable it to load the Web page correctly.
2
Click
Settings
>
Security
>
Disk Encryption
.
Note:
Disk Encryption appears in the Security Menu only when a formatted, non
‑
defective printer hard disk is
installed.
3
From the Disk Encryption menu, select either of the following:
•
Disable
—Use this to disable disk encryption.
•
Enable
—Use this to enable disk encryption.
Notes:
–
Disable is the factory default setting.
–
Changing this setting will cause the printer to undergo a power
‑
on reset.
Warning—Potential Damage:
Changing the setting for disk encryption will erase the contents of the hard
disk.
4
Click
Submit
to proceed with disk wiping and encryption.
Note:
Encryption takes approximately two minutes.
Warning—Potential Damage:
Do not turn off the printer during the encryption process.
5
Click
Refresh
to return to the Embedded Web Server.
Using the printer control panel
1
Turn off the printer.
2
Hold down
2
and
6
while turning the printer on. Release the buttons only when the screen with the progress bar
appears.
The printer performs a power-on sequence, and then the Configuration menu appears. When the printer is fully
turned on, a list of functions appears on the printer display.
3
Touch
Disk Encryption
>
Enable
.
4
Touch
Yes
to proceed with disk encryption.
Notes:
•
Do not turn off the printer during the encryption process. Doing so may result in loss of data.
•
Encryption takes approximately two minutes.
•
A status bar will indicate the progress of the disk wiping task. After the disk has been encrypted, the printer
will return to the Enable/Disable screen.
5
Touch
Back
>
Exit Config Menu
.
The printer will perform a power
‑
on reset, and then return to normal operating mode.
Using security features in the Embedded Web Server
37