Lexmark T630 Setup Guide - Page 61

Step8: Con for TCP/IP, Assigning a printer IPaddress - manual

Get Lexmark T630 - Printer - B/w PDF manuals and user guides
UPC - 734646385756
View all Lexmark T630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Step 8: Configure for TCP/IP If you have TCP/IP available on your network, we recommend that you assign an IP address to the printer. Assigning a printer IP address Note: Standard Network appears if you purchased a printer with a network port on the printer system board. If you have a MarkNet print server installed in option card slot 1 or 2, you see Network Option 1 or Network Option 2. If your network is using DHCP, an IP address is automatically assigned after you connect the network cable to the printer. 1 Look for the address under the "TCP/IP" heading on the network setup page you printed in "Printing a network setup page" on page 54. 2 Go to "Verifying the IP settings" on page 57 and begin with step 2. If your network is not using DHCP, then you must manually assign an IP address to the printer. An easy way to do this is to use the printer operator panel: 1 Press Menu until you see Network Menu, and then press Select. 2 Press Menu until you see Standard Network, and then press Select. 3 Press Menu until you see Std Net Setup (or Network 1 Setup or Network 2 Setup), and then press Select. 4 Press Menu until you see TCP/IP, and then press Select. 5 Press Menu until you see Set IP Address, and then press Select. 6 Change the address by pressing Menu to increase or decrease each number. Press Select to move to the next segment. Press Select when you are finished. The message Saved appears briefly. 7 Press Menu until you see Set IP Netmask, and then press Select. Configure for TCP/IP 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
56
Configure for TCP/IP
Step 8: Configure for TCP/IP
P/IP
If you have TCP/IP available on your network, we recommend that you
assign an IP address to the printer.
Assigning a printer
IP address
If your network is using DHCP
, an IP address is automatically assigned
after you connect the network cable to the printer.
1
Look for the address under the “TCP/IP” heading on the
network setup page you printed in “Printing a network
setup page” on page 54.
2
Go to “Verifying the IP settings” on page 57 and begin with
step 2.
If your network is not using DHCP
, then you must manually assign an
IP address to the printer.
An easy way to do this is to use the printer operator panel:
Note:
Standard Network
appears if you purchased a
printer with a network port on
the printer system board. If
you have a MarkNet print
server installed in option
card slot 1 or 2, you see
Network Option 1 or Network
Option 2.
1
Press
Menu
until you see Network Menu, and then press
Select
.
2
Press
Menu
until you see Standard Network, and then press
Select
.
3
Press
Menu
until you see Std Net Setup (or Network 1 Setup or
Network 2 Setup), and then press
Select
.
4
Press
Menu
until you see TCP/IP, and then press
Select
.
5
Press
Menu
until you see Set IP Address, and then press
Select
.
6
Change the address by pressing
Menu
to increase or decrease
each number. Press
Select
to move to the next segment. Press
Select
when you are finished.
The message
Saved
appears briefly.
7
Press
Menu
until you see Set IP Netmask, and then press
Select
.