Lexmark WinWriter 100 Service Manual

Lexmark WinWriter 100 Manual

Get Lexmark WinWriter 100 PDF manuals and user guides View all Lexmark WinWriter 100 manuals
Add to My Manuals
Save this manual to your list of manuals

Lexmark WinWriter 100 manual content summary:

  • Lexmark WinWriter 100 | Service Manual - Page 1
    WinWriter™ 100 4076-001 • Table of Contents • Start Diagnostics • Safety and Notices • Trademarks • Index • Manuals Menu Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries.
  • Lexmark WinWriter 100 | Service Manual - Page 2
    (August,1994) THE FOLLOWING PARAGRAPH DOES NOT APPLY TO THE UNITED KINGDOM OR ANY COUNTRY WHERE SUCH PROVISIONS ARE INCONSISTENT WITH LOCAL LAW: LEXMARK INTERNATIONAL, INC. PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
  • Lexmark WinWriter 100 | Service Manual - Page 3
    For Service 2 Diagnostic Information 3 Start 3 Error Indicator Table 4 Power-on-self-test (POST) Sequence 5 POST Symptom Table 5 Symptom Tables 6 Carrier Transport Problems 6 Communications Problem 6 Maintenance Station Problems 6 Operator Panel Problems 6 Paper Feed Problems 7 Power
  • Lexmark WinWriter 100 | Service Manual - Page 4
    Service Checks 8 Envelope Feed Service Check 8 First Print Line Service Check 8 Maintenance Station Service Check 9 Operator Panel Service Check 10 Paper Feed Service Check 10 Paper Path Service Check 13 Parallel Port Service Check 14 Power Service Check 14 Print Quality Service Guide
  • Lexmark WinWriter 100 | Service Manual - Page 5
    4076-0WJ Repair Information, Removal Procedures (continued) Paper Ejectors Removal 32 Paper Feed Motor Removal 32 Paper Guide Removal 32 Paper Release Lever Removal 33 Power Supply Removal 33 Print Head Cable Removal 34 Right Side Frame Removal 35 Rubber Backer Removal 36
  • Lexmark WinWriter 100 | Service Manual - Page 6
    other products, programs, or services, except those expressly designated by your country. Federal Communications Commission (FCC) Statement This printer has been tested and found to comply with the installed and used in accordance with the instructions, may cause harmful interference to radio
  • Lexmark WinWriter 100 | Service Manual - Page 7
    • Consult your point of purchase or service representative for additional suggestions. The manufacturer is comply with FCC regulations on electromagnetic interference, for a Class B computing device, the printer cable must be shielded. To assure compliance with FCC regulations for a Class B
  • Lexmark WinWriter 100 | Service Manual - Page 8
    relating to electromagnetic compatibility. Germany A declaration of conformity with the requirements of the Directive has been signed by the Director of Manufacturing and Technical Support, Lexmark International, Ltd., Boigny, France. This product satisfies the Class B limits of EN 55022. viii
  • Lexmark WinWriter 100 | Service Manual - Page 9
    code table, symptom table, and service checks used to isolate failing field replaceable units (FRUs). 3. "Diagnostic Aids" contains tests and checks used to locate or repeat symptoms of printer problems. 4. "Repair Information" provides instructions for making printer adjustments and removing and
  • Lexmark WinWriter 100 | Service Manual - Page 10
    to be used by others. • There may be an increased risk of electric shock and per- sonal injury during disassembly and servicing of this product. Professional service personnel should understand this and take necessary precautions. • The safety features of some parts may not always be obvi- ous
  • Lexmark WinWriter 100 | Service Manual - Page 11
    med henblik pa professionelt servicepersonale, og bor derfor ikke benyttes af andre. • Risikoen for elektrisk stod oges under demontering og service af dette produkt, hvorfor der bor tages de nodvendige forholdsregler. • Sikkerhedsforanstaltningerne er ikke altid lige apenbare for alle reservedele
  • Lexmark WinWriter 100 | Service Manual - Page 12
    4076-0WJ General Information 7 The WinWriter 100 4076 OWJ is a general purpose high-quality ink jet printer with a customer-replaceable print cartridge containing the ink and the print head. With a total of 56 nozzles in the print head it can print at speeds of 167 cps in Letter Quality mode
  • Lexmark WinWriter 100 | Service Manual - Page 13
    Assemblies Problem Isolation Charts Picture Element Power-On Self Test Print Quality Enhancement Technology Printer Sharing Option Static Random Access Memory Used Parts Replacement Volts alternating current Volts direct current Zero Insertion Force Unique Tools Required For Service
  • Lexmark WinWriter 100 | Service Manual - Page 14
    this chapter to determine the failing part in a malfunctioning printer. Start Service error indications show up as a series of flashes of the error indicator table and take the indicated action for that error. The printer also logs the last occurring error. If you think you may have an intermittent
  • Lexmark WinWriter 100 | Service Manual - Page 15
    /or the system board Go to the "Maintenance Station Service Check" on page 9. Go to the "Transport Service Check" on page 17. Go to the "Transport Service Check" on page 17. Go to the "Transport Service Check" on page 17. Go to the "Transport Service Check" on page 17. Go to the "Maintenance Station
  • Lexmark WinWriter 100 | Service Manual - Page 16
    test (POST) Sequence When you turn the printer on it performs a POST. Turn your Service Check" on page 14. Go to the "First Print Line Service Check" on page 8. Go to the "Paper Feed Service Check" on page 10. Go to the "Transport Service Check" on page 17. Go to the "Maintenance Station Service
  • Lexmark WinWriter 100 | Service Manual - Page 17
    following tables and take the appropriate action. Carrier Transport Problems SYMPTOM • No carrier movement • Slow carrier movement • Carrier stops Communications Problem ACTION Go to the "Transport Service Check" on page 17. SYMPTOM Printer not communicating with host. ACTION Go to the "Parallel
  • Lexmark WinWriter 100 | Service Manual - Page 18
    in machine, no Power On light, no motors Print Quality Problems ACTION Go to the "Power Service Check" on page 14. SYMPTOM • Voids in characters • • Vertical alignment off • Ink smearing • Vertical streaks on paper • Print lines crowded ACTION Go to the "Print Quality Service Check" on page 15.
  • Lexmark WinWriter 100 | Service Manual - Page 19
    have been turned to the envelope load positions Be sure the envelope guides are against the envelopes Go to and perform the "Paper Feed Service Check" on page 10. First Print Line Service Check FRU OR PROCEDURE 1 End-of-Forms Flag 2 End-of-Forms Sensor 3 System Board 4 Feed Arm Assembly 5 Operator
  • Lexmark WinWriter 100 | Service Manual - Page 20
    4076-0WJ Maintenance Station Service Check The maintenance station has two functions: 1. Cleans the print for binds and loose or worn parts in the drive assembly. Also check the motor gear Turn the printer off and disconnect J4 from the system board. Turn the machine on and check for a pulse of
  • Lexmark WinWriter 100 | Service Manual - Page 21
    the power supply to the system board. Turn the printer on Check for +5 V dc at test point CE Service Check If your machine does not have paper jam problems, go on to the service check. If your machine does have a paper jam problem guide is on top of the paper guide. Diagnostic Information 10
  • Lexmark WinWriter 100 | Service Manual - Page 22
    turn, can be caused by: • An open or short in the motor • An open or short in the motor driver on the system board • A bind in the paper feed mechanism Check for 100 ohms (±20 ohms) between the following pins on the motor: Pin 1 to Pin 4 Pin 2 to Pin 4 Pin 3 to Pin
  • Lexmark WinWriter 100 | Service Manual - Page 23
    binds, and worn or broken parts. Check the following for wear or damage: Pick Rollers Envelope Bucklers All parts inside the left and right edge guides Check for binds or damage. Check for worn or binding rollers. Check for broken star roller springs. After the paper exits from the exit rollers
  • Lexmark WinWriter 100 | Service Manual - Page 24
    the following before you begin this service check: • Check the entire paper path for obstructions. • Be sure the paper guides are not worn or broken and wear or damage: Envelope Bucklers All parts inside the left and right edge guides Check for binds or damage. Check for wear or binds. Check for
  • Lexmark WinWriter 100 | Service Manual - Page 25
    Check FRU OR PROCEDURE 1 Parallel Port Power Service Check ACTION Run a test page to be sure the printer can print. Run the"Parallel Port Test" on page 19. If the test fails, replace the system board. FRU OR PROCEDURE 1 Power Supply 2 Operator Panel 3
  • Lexmark WinWriter 100 | Service Manual - Page 26
    Print Quality Service Check FRU OR PROCEDURE ACTION 1 Print Cartridge Be sure the machine has a known good print cartridge. 2 Print Head Carrier Assembly Reseat the print head cable in the system board and check the following parts for wear or damage: 3 Purge Test Print Cartridge Latch Latch
  • Lexmark WinWriter 100 | Service Manual - Page 27
    "Maintenance Station Service Check" on page 9, then return to this check. Ink smudging and smearing can be caused by paper problems or problems in the paper be caused by problems in the transport area. Check the following: • Transport belt for wear. • Carrier guide and carrier guide rod for wear or
  • Lexmark WinWriter 100 | Service Manual - Page 28
    remains, replace the system board. Turn the printer off and disconnect J6 from the system board. Turn the printer on and check for a pulse of 3 to board. A problem with the maintenance station can cause carrier movement problems at the right margin. Go to the "Maintenance Station Service Check" on
  • Lexmark WinWriter 100 | Service Manual - Page 29
    line is the print cartridge nozzle pattern. The six black lines are the purge pattern. These tests are used to verify all print cartridge nozzles are working. There the printer on a PC and run the bi-directional alignment adjustment procedure on the service manual diskette. Diagnostic Aids 18
  • Lexmark WinWriter 100 | Service Manual - Page 30
    before you start the test. This test performs a wraparound test between the printer parallel port and the parallel port test connector. If the test is remains off. Encoder Sensor Test J12 The printer motors are disabled during this test to allow you to manually move the carrier to verify the encoder
  • Lexmark WinWriter 100 | Service Manual - Page 31
    reset the error log to zero. The paper sensor must be open to perform this function. To do this, place a piece of paper in the manual paper feed slot before you turn the machine on. Resetting the error log allows you to track new errors. The error log is especially helpful
  • Lexmark WinWriter 100 | Service Manual - Page 32
    printer and how to remove defective parts. WARNING: Read the following before handling electronic parts. Handling ESD-sensitive Parts Many electronic products use parts that are known to be sensitive to electrostatic discharge (ESD). To prevent damage to ESD-sensitive parts, follow the instructions
  • Lexmark WinWriter 100 | Service Manual - Page 33
    is correct when the vertical bars appear straight. To adjust the bi-directional alignment: 1. Attach the printer to a PC operating in DOS. 2. Load paper in the Auto Sheet Feed. 3. Place the 4076 OWJ Service Diskette in the diskette drive. Type the letter of the drive, colon, and adjust. For example
  • Lexmark WinWriter 100 | Service Manual - Page 34
    4076-0WJ Removal Procedures The following procedures are arranged in alphabetical order according to the name of the printer part discussed. When there is artwork to support a procedure, it follows the text. Releasing Plastic Latches Many of the parts are held in place with plastic latches. To
  • Lexmark WinWriter 100 | Service Manual - Page 35
    4076-0WJ Auto Sheet Feed (ASF) Removal 1. Remove the top cover. 2. Push in the two latches [A] that secure the auto sheet feed to the side frame, then lift up the auto sheet feed to remove it from the machine. A A When you reinstall the auto sheet feed, be sure the feed arm assembly is vertical,
  • Lexmark WinWriter 100 | Service Manual - Page 36
    ASF Right And Left Edge Guide Assemblies Removal 1. Remove the auto sheet feed. 2. Remove the manual insert tray by prying one the mounting stud. Carrier Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Disconnect the print head cables from the system board. 4. Move the carrier in
  • Lexmark WinWriter 100 | Service Manual - Page 37
    THE TOP OF THE BELT INTO THE TOP GRIP. Carrier Guide Removal You may remove the carrier guide without removing the covers if you carefully follow this procedure. 1. Open and remove the access cover. 2. Remove the print cartridge. 3. Rotate the carrier guide rod top-to-rear to unlock the rod latches
  • Lexmark WinWriter 100 | Service Manual - Page 38
    end of the rod, to the rear and lift up the rod until the sensor on the carrier clears the encoder strip. Remove the carrier guide rod through the opening in the left side frame. Be careful not to damage the encoder strip. A latch on the top front end of each
  • Lexmark WinWriter 100 | Service Manual - Page 39
    the rear and lift up the rod until the sensor on the carrier clears the encoder strip. Place the carrier on top of the paper guide. 5. Remove the encoder strip from the left mounting peg. To do this, push the right latch slightly to the left. 6. Remove the encoder strip from
  • Lexmark WinWriter 100 | Service Manual - Page 40
    Disconnect the print head cables from the system board. 4. Remove the paper guide. 5. Remove the C-clip from the feed arm assembly and remove the feed Left Side Frame Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Remove the auto sheet feed. 4. Disconnect the print head cables
  • Lexmark WinWriter 100 | Service Manual - Page 41
    the middle frame, align the right side frame latch with the latching surface on the middle frame before you align the roller shafts and carrier guide. It may be easier to do this with the machine on its right side. Maintenance Drive And Rocker Assemblies Removal 1. Remove the top cover. 2. Remove
  • Lexmark WinWriter 100 | Service Manual - Page 42
    4076-0WJ Middle Frame Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Remove the auto sheet feed. 4. Disconnect the print head cables from the system board. 5. Disconnect J4, J5, and J6 from the system board. 6. Remove the
  • Lexmark WinWriter 100 | Service Manual - Page 43
    1. Remove the top cover. 2. Disconnect the paper feed motor from the system board. 3. Remove the motor mounting screws and remove the motor. Paper Guide Removal 1. Remove the top cover. 2. Remove the auto sheet feed. 3. Disconnect the print head cables from the system board. 4. Pull the ends of
  • Lexmark WinWriter 100 | Service Manual - Page 44
    Paper Release Lever Removal 1. Remove the top cover. 2. Pull the paper release lever forward. 3. Place a screw driver into the slot [A] of the paper release lever. Push the screw driver down to release the latch, then remove the lever. A Power Supply Removal 1. Remove the top cover. 2. Disconnect
  • Lexmark WinWriter 100 | Service Manual - Page 45
    4076-0WJ Print Head Cable Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Remove the carrier. 4. Remove the cable clip [A] from the left side of the carrier. 5. Remove the pointer from the front of the carrier. A 6. Remove the 2
  • Lexmark WinWriter 100 | Service Manual - Page 46
    Side Frame Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Remove the auto sheet feed. 4. Disconnect the print head until the sensor on the carrier clears the encoder strip. Remove the carrier rod guide through the opening in the left side frame. Be careful not to damage the
  • Lexmark WinWriter 100 | Service Manual - Page 47
    left side. Rubber Backer Removal 1. Remove the top cover. 2. Remove the print cartridge. 3. Remove the print head cable. 4. Remove the rubber backer from the carrier. clears the encoder strip. Place the carrier on top of the paper guide. 5. A latch on the top front end of each side frame holds
  • Lexmark WinWriter 100 | Service Manual - Page 48
    4076-0WJ System Board Removal 1. Remove the top cover. 2. Disconnect the print head cables from the system board. 3. Disconnect connectors J4, J5, and J6 from the system board. Remove the machine from the base. To do this, push the frame latches out as you lift the machine from the base. Set the
  • Lexmark WinWriter 100 | Service Manual - Page 49
    4076-0WJ Top Cover Removal 1. Unplug the power cord and the interface cable from the back of the printer. 2. Unlatch the auto sheet feed left cover by pushing it up from the bottom, then slide it off the machine. 3. Turn the machine around to
  • Lexmark WinWriter 100 | Service Manual - Page 50
    4076-0WJ Connector Locations 9 This chapter shows the locations of major printer assemblies, connectors, and ground straps. System Board Connectors J9 U20 1 S1 U23 J11 1 J12 1 J7 J1 1 J6 1 J5 J4 1 1 J2 J10 1 .CE/TP Connector Locations 39
  • Lexmark WinWriter 100 | Service Manual - Page 51
    4076-0WJ Connector J1 J2 J4 J5 J6 J9 J10 J11 J12 U20 Connector Names Print Head Cable Print Head Cable Maintenance Motor Paper Feed Motor Transport Motor Parallel Port Operator Panel Power Supply Test Jumper Code Module Connector Locations 40
  • Lexmark WinWriter 100 | Service Manual - Page 52
    chapter contains the lubrication specifications. Following these recommendations can help prevent problems and maintain optimum performance. Lubrication Specifications Lubricate only when parts frame. Do not lubricate the carrier guide rod, or carrier guide rod bearings. Preventive Maintenance 41
  • Lexmark WinWriter 100 | Service Manual - Page 53
    4076-0WJ Parts Catalog 11 How To Use This Parts Catalog • SIMILAR ASSEMBLIES: If two assemblies contain a major- ity of identical parts, they are broken down on the same list. Common parts are shown by one index number. Parts peculiar to one or the other of the assemblies are listed separately
  • Lexmark WinWriter 100 | Service Manual - Page 54
    4076-0WJ Assembly 1: Covers 2 6 5 9 7 4 8 1 3 43
  • Lexmark WinWriter 100 | Service Manual - Page 55
    1-1 -2 -3 -4 -5 -6 -7 -8 -9 Part Number 1367099 1367487 1367486 1367479 1367493 1374401 1374409 Units 1 1 1 1 1 1 1 1 1 Description Top Cover Access Cover Asm Font Card Door Rear Cover Left Output Guide Logo Screw, Parts Packet 1367169 Washer, Parts Packet 1367169 Microsoft at Work Label 44
  • Lexmark WinWriter 100 | Service Manual - Page 56
    4076-0WJ Assembly 2: Frames 7 2 3 4 5 1 6 45
  • Lexmark WinWriter 100 | Service Manual - Page 57
    4076-0WJ AsmIndex 2-1 -2 -3 -4 -5 -6 -7 Part Number 1367489 1367209 1367219 1367229 1367309 1367199 1367079 Units 1 1 1 1 1 1 1 Description Base Asm Left Side Frame Middle Frame Asm Right Side Frame Carrier Transport Motor Frame Exit Tray Asm Carrier Guide 46
  • Lexmark WinWriter 100 | Service Manual - Page 58
    4076-0WJ Assembly 3: Paper Feed 1 2 5 3 4 6 7 8 9 47
  • Lexmark WinWriter 100 | Service Manual - Page 59
    -7 -8 -9 Part Number 1367179 1367339 1367279 1367289 1367266 1367049 1367269 Units 1 2 1 1 1 1 3 1 1 Description Paper Release Lever Bushing, Parts Packet1367169 Paper Guide Small Feed Roller Asm Exit Roller Asm Ejector B/M Spring, Parts Packet1367169 End of Forms Flag Large Feed Roller Asm 48
  • Lexmark WinWriter 100 | Service Manual - Page 60
    4076-0WJ Assembly 3: Paper Feed (Cont.) 13 12 11 49 14 10 11
  • Lexmark WinWriter 100 | Service Manual - Page 61
    4076-0WJ AsmIndex 3-10 -11 -12 -13 -14 Part Number 1367239 1367249 1367259 Units 1 1 1 2 2 Description Paper Feed Motor Asm Gears B/M Feed Arm Asm C-Clip, Parts Packet 1367169 Screw, Parts Packet 1367169 50
  • Lexmark WinWriter 100 | Service Manual - Page 62
    4076-0WJ Assembly 4: Electronics 5 4 4 3 2 51 1 8 11 6 10 7 9
  • Lexmark WinWriter 100 | Service Manual - Page 63
    4076-0WJ AsmIndex 4-1 -2 -3 -4 -5 -6 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 Part Number 1374402 1367189 1430317 1342536 1339520 1339520 1342514 1342514 1342530 1430317 1342534 1342514 1342514 1339525 1342514 1342514 1339520 1339520 1339520 1339520
  • Lexmark WinWriter 100 | Service Manual - Page 64
    4076-0WJ Assembly 4: Electronics (Cont.) 5 4 4 3 2 53 1 8 11 6 10 7 9
  • Lexmark WinWriter 100 | Service Manual - Page 65
    4076-0WJ AsmIndex -7 -7 -7 -7 -7 -7 -7 -7 -7 -7 -8 -9 -10 -NS Part Number 1342514 1339520 1339523 1339520 1339520 1339522 1339520 1339519 1342536 1342514 1374399 1374327 1374328 Units 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description Power Cord, Peru Power Cord, Portugal Power Cord, South Africa Power
  • Lexmark WinWriter 100 | Service Manual - Page 66
    4076-0WJ Assembly 4 Electronics (Cont.) 13 12 9 10 11 55
  • Lexmark WinWriter 100 | Service Manual - Page 67
    4076-0WJ AsmIndex 4-9 -10 -11 -12 -13 Part Number 1374403 1374404 1374408 1374406 Units 1 1 3 1 1 Description Operator Panel Card Operator Panel Cable Screw, Parts Packet 1367169 Power Button Op Panel Cover 56
  • Lexmark WinWriter 100 | Service Manual - Page 68
    4076-0WJ Assembly 5: Carrier 1 3 2 5 1 4 6 57
  • Lexmark WinWriter 100 | Service Manual - Page 69
    4076-0WJ AsmIndex 5-1 -2 -3 -4 -5 -6 NS Part Number 1367299 1367149 1367109 1367089 1374338 Units 1 1 2 1 1 1 1 Description Print Head Carrier Asm Cable, Print Head Screw, Parts Packet 1367169 Rubber Backer Guide Rod, Carrier Clip, Parts Packet 1367169 Toroid, Non-Western Hemisphere 58
  • Lexmark WinWriter 100 | Service Manual - Page 70
    4076-0WJ Assembly 6: Carrier Transport 1 7 2 6 3 5 4 59
  • Lexmark WinWriter 100 | Service Manual - Page 71
    4076-0WJ AsmIndex 6-1 -2 -3 -4 -5 -6 -7 Part Number 1367319 1367359 1367379 1367349 1367329 Units 1 2 1 1 1 5 1 Description Motor Asm Screw, Parts Packet 1367169 Belt Encoder Strip Star Roller Asm Spring, Parts Packet 1367169 Idler Pulley B/M 60
  • Lexmark WinWriter 100 | Service Manual - Page 72
    4076-0WJ Assembly 7: Auto Sheet Feed 6 11 10 3 10 8 13 4 12 2 5 7 1 14 9 61
  • Lexmark WinWriter 100 | Service Manual - Page 73
    and Width Adjust Strip Left Edge Guide Asm Upper Paper Support Pick Roll and Paper Load Shaft B/M Pick Roll Hub Asm Left Side Cover Right Side Cover Paper Load B/M Envelope Buckler B/M Side and Back Plate B/M Gears B/M E-Ring, Parts Packet 1367169 Screw, Parts Packet 1367169 Manual Insert Tray 62
  • Lexmark WinWriter 100 | Service Manual - Page 74
    4076-0WJ Assembly 8: Maintenance Station 3 1 2 4 63
  • Lexmark WinWriter 100 | Service Manual - Page 75
    4076-0WJ AsmIndex 8-1 -2 -3 -4 Part number 1367369 1367399 1367389 Units 1 1 1 2 Description Rocker Asm Drive Asm Wiper and Cap B/M Screw, Parts Packet 1367169 64
  • Lexmark WinWriter 100 | Service Manual - Page 76
    Removal 26 Carrier Guide Removal 26 Carrier Problem 6 Connector Locations 39 D Diagnostic Information 3 E Encoder Strip Removal 28 End-of-forms Flag Removal 28 Envelope Feed Service Check 8 Error Indicator Table 4 Exit Roller Assembly Removal 28 F Feed Arm Assembly Removal 29 First Print Line Service
  • Lexmark WinWriter 100 | Service Manual - Page 77
    Assemblies Removal 30 Maintenance Station Problems 6 Maintenance Station Service Check 9 O Operator Panel Problems 6 Operator Panel Removal 31 Operator Panel Service Check 10 Outside Idler Gears Removal 31 P Paper Feed Problems 7 Paper Feed Service Check 10 Paper Path Service Check 13 Parallel Port
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
4076-001
WinWriter™ 100
Lexmark and Lexmark with diamond
design are trademarks of Lexmark
International, Inc., registered in the
United States and/or other countries.
• Table of Contents
• Index
• Safety and Notices
• Trademarks
• Start Diagnostics
• Manuals Menu