LiftMaster 8355 8355 Manual - Page 14

Install the Door Control - lowes

Get LiftMaster 8355 PDF manuals and user guides View all LiftMaster 8355 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Install the Door Control 1 Install the door control INTRODUCTION Compatible with MyQ® and Security+ 2.0™ To prevent possible SERIOUS INJURY or DEATH from electrocution: • Be sure power is NOT connected BEFORE installing door control. • Connect ONLY to 12 VOLT low voltage wires. accessories, see page 37. Your garage door opener is compatible with up to 2 Smart Control Panels or 4 of any other Security+ 2.0™ door controls. NOTE: Older LiftMaster door controls To prevent possible SERIOUS INJURY or DEATH from a closing garage door: and third party products are not compatible. • Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door. Install the door control within sight of the door at • NEVER permit children to operate or play with door control push buttons or remote control transmitters. • Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from the moving parts of the door. NOTE: Your product may look different than • ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of moving parts of the door the illustrations. closing garage door. Screw 6ABx1" Screw 6-32x1" HARDWARE Drywall Anchors NOTE: For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box. 1.1 Strip 7/16 inch (11 mm) of insulation from 1.2 Connect one wire to each of the two screws 1.3 Mark the location of the bottom mounting one end of the wire and separate the wires. on the back of the door control. The wires hole and drill a 5/32 inch (4 mm) hole. can be connected to either screw. 7/16" (11 mm) PRE-WIRED INSTALLATIONS: Choose Wall any two wires to connect, note which wires are used so the correct wires are connected at the garage door opener in a later step. 1.4 Install the bottom screw, allowing 1/8 inch (3 mm) to protrude from the wall. DRYWALL Drywall Anchor Screw 6AB x 1" GANG BOX Screw 6-32 x 1" 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
14
1
Install the door control
Install the Door Control
To prevent possible SERIOUS INJURY or DEATH from electrocution:
•
Be sure power is NOT connected BEFORE installing door control.
•
Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
•
Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet
(1.5 m), and away from ALL moving parts of door.
•
NEVER permit children to operate or play with door control push buttons or remote control
transmitters.
•
Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
•
ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of
closing garage door.
INTRODUCTION
Compatible with MyQ
®
and Security
+
2.0™
accessories,see page 37.Your garage door
opener is compatible with up to 2 Smart Control
Panels or 4 of any other Security
+
2.0™ door
controls.
NOTE:
Older LiftMaster door controls
and third party products are not compatible.
Install the door control within sight of the door at
a minimum height of 5 feet (1.5 m) where small
children cannot reach, and away from the
moving parts of the door.
NOTE:
Your product may look different than
moving parts of the door the illustrations.
Screw
6ABx1"
HARDWARE
Drywall
Anchors
Screw
6-32x1"
NOTE:
For gang box installations it is not necessary to drill holes or install the drywall anchors. Use the existing holes in the gang box.
1.1
Strip 7/16 inch (11 mm) of insulation from
one end of the wire and separate the wires.
7/16"
(11 mm)
1.2
Connect one wire to each of the two screws
on the back of the door control. The wires
can be connected to either screw.
PRE-WIRED INSTALLATIONS:
Choose
any two wires to connect, note which wires
are used so the correct wires are connected
at the garage door opener in a later step.
1.3
Mark the location of the bottom mounting
hole and drill a 5/32 inch (4 mm) hole.
Wall
1.4
Install the bottom screw, allowing 1/8 inch
(3 mm) to protrude from the wall.
Screw
6-32 x 1"
DRYWALL
GANG BOX
Screw
6AB x 1"
Drywall Anchor