Home » LiftMaster Manuals » Garage Door Openers » LiftMaster 8550W » Manual Viewer

LiftMaster 8550W 8550W Owners Manual - Page 43

Model 8550W, Contact Information - logic board

Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Repair Parts Model 8550W Garage Door Opener Parts 9 4 3 6 114A4831B 10 8 7 1 5 11 2 4 3 Description 1 Sprocket and Sprocket Cover with Screws 2 End Panel with battery cover and light socket 3 Light Lens 4 Light Socket 5 Transformer 6 Cover 7 Motor with Travel Module 8 Travel Module 9 End Panel and light socket 10 Receiver Logic Board 11 Backup Battery Part Number 041C589-2 041A7618 041A7562 041C0279 041D0277-1 041D8257 041D1739-1 041A7114-7 041D8198 050DCTWF 485LM Contact Information Address repair parts order to: LiftMaster 6050 S. Country Club Rd. Tucson, AZ 85706 For installation and service information call: 1-800-528-9131 Or visit us online at: LiftMaster.com or myLiftMaster.com Before calling, please have the model number of the garage door opener. If you are calling about a troubleshooting issue, it is recommended that you have access to your garage door opener while calling. If you are ordering a repair part please have the following information: part number, part name, and model number. Wi-Fi® is a registered trademark of Wi-Fi Alliance. © 2015, LiftMaster All Right4s3Reserved

Section	Page
Wi-Fi® Garage Door Opener Belt Drive Models 8550W and 8550W-267	1
Contents	2
Preparation	3
MyQ® Serial Number	3
Safety Symbol and Signal Word Review	3
Unattended Operation	3
Test the Wi-Fi® Signal Strength	4
Before You Begin	4
Test the Wi-Fi® Signal Strength	4
Check the Door	4
Tools Needed	5
Carton Inventory	6
Installation	6
Door Control Hardware	6
Assembly	7
1 Attach the Rail to the Garage Door Opener	7
2 Tighten the Belt	8
Installation	10
1 Determine the Header Bracket Location	10
2 Install the Header Bracket	11
3 Attach the Rail to the Header Bracket	12
4 Position the Garage Door Opener	12
5 Hang the Garage Door Opener	13
6 Install the Light Bulbs	14
7 Attach the Emergency Release Rope and Handle	14
8 Install the Door Bracket	15
9 Connect the Door Arm to the Trolley	16
Install the Door Control	17
2 Wire the door control to the garage door opener	18
3 Attach the warning labels	18
Install the Protector System®	19
1 Install the Safety Reversing Sensors	20
2 Wire the Safety Reversing Sensors	21
Power	23
1 Connect Power	23
2 Ensure the Safety Reversing Sensors are Aligned	24
3 Ensure the Door Control is Wired Correctly	24
Adjustments	25
Introduction	25
PROGRAMMING BUTTONS	25
1 Program the Travel	26
2 Test the Safety Reversal System	27
3 Test the Protector System®	27
Battery Backup* if applicable	28
1 Install the Battery	28
2 Test the Battery	28
Charge the Battery	29
Battery Status LED	29
Operation	30
Get Connected with MyQ®	32
1. ACTIVATE WI-FI LEARN MODE	32
2. CONNECT TO THE MyQ® Wi-Fi NETWORK	32
3. CONNECT THE GARAGE DOOR OPENER TO YOUR HOME WI-FI NETWORK	32
4. SETUP YOUR MyQ® ACCOUNT	32
If you need help adding devices to you MyQ account, or to learn more go to wi...	32
Using the Door Control	33
SYNCHRONIZE THE DOOR CONTROL	33
PUSH BAR	33
NAVIGATION BUTTONS	33
LIGHT BUTTON	33
SCREEN	33
LEARN A DEVICE	33
LOCK	33
TIMER-TO-CLOSE (TTC)	33
AUTOIMATIC LIGHT	33
MAINTENANCE ALERT (MAS)	33
Setup	34
SCREEN	34
FEATURES	34
SETTINGS	34
SERVICE	34
Remote Control	35
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PINUSING THE DOOR CONTROL	35
PROGRAM USING THE LEARN BUTTON ON THE GARAGE DOOR OPENER	35
To Erase the Memory	36
Maintenance	37
Maintenance Schedule	37
The Remote Control Battery	37
Troubleshooting	38
Accessories	40
LIFTMASTER® LIMITED WARRANTY	41
Repair Parts	42
Rail Assembly Parts	42
Installation Parts	42