LiftMaster 8557 8557 Elite Series Users Guide Manual - Page 4

Operation - model

Page 4 highlights

Operation Your garage door opener is equipped with features to provide you with greater control over your garage door operation. Accessories provided with your garage door opener will vary depending on the garage door opener model purchased. ALERT2CLOSE The Alert2Close feature provides a visual and an audible alert that an unattended door is closing. TIMER-TO-CLOSE (TTC) The Timer-to-Close feature automatically closes the door after a specified time period that can be adjusted using a TTC enabled door control (Models 881LM or 880LM). Prior to and during the door closing the garage door opener lights will flash and the garage door opener will beep. MyQ™ MyQ™ technology uses a 900MHz signal to provide two-way communication between the garage door opener and MyQ™ enabled accessories. Your garage door opener is compatible with up to 16 MyQ™ accessories. if you hold the button on the door control or keyless entry until the door is fully closed. The safety reversing sensors do not affect the opening cycle. ENERGY CONSERVATION For energy efficiency the garage door opener will enter sleep mode when the door is fully closed. The sleep mode shuts the garage door opener down until activated. The sleep mode is sequenced with the garage door opener light bulb; as the light bulb turns off the sensor LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will light. LIGHTS The garage door opener light bulbs will turn on when the opener is initially plugged in; power is restored after interruption, or when the garage door opener is activated. The lights will turn off automatically after 4-1/2 minutes. An incandescent A19 light bulb (100 watt maximum) or for maximum energy efficiency a 26 W (100 W equivalent) compact fluorescent light (CFL) bulb may be used. Light Feature REMOTE CONTROLS AND DOOR CONTROLS (SECURITY✚ 2.0™) Your garage door opener has already been programmed at the factory to operate with your remote control, which changes with each use, randomly accessing over 100 billion new codes. Compatible with MyQ™ and Security✚ 2.0™. NOTE: Older LiftMaster remote controls, door controls, and third party products are not compatible. Accessories (Security✚ 2.0™) MEMORY CAPACITY Remote Controls Up to 40 Door Controls Up to 2 Smart Control Panels or 4 of any other Security+ 2.0™ door controls Keyless Entries Up to 4 THE PROTECTOR SYSTEM® (SAFETY REVERSING SENSORS) The garage door opener is equipped with an added feature; the lights will turn on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken. For added control over the light bulbs on your garage door opener, see page 6. USING YOUR GARAGE DOOR OPENER The garage door opener can be activated through a wall-mounted door control, remote control, wireless keyless entry or MyQ™ accessory. When the door is closed and the garage door opener is activated the door will open. If the door senses an obstruction or is interrupted while opening the door will stop. When the door is in any position other than closed and the garage door opener is activated the door will close. If the garage door opener senses an obstruction while closing, the door will reverse. If the obstruction interrupts the sensor beam the garage door opener lights will blink 10 times. However, you can close the door if you hold the button on the door control or keyless entry until the door is fully closed. The safety reversing sensors do not affect the opening cycle. The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. When properly connected and aligned, the safety reversing sensors will detect an obstruction in the path of the infrared beam. If an obstruction breaks the infrared beam while the door is closing, the door will stop and reverse to full open position, and the opener lights will flash 10 times. If the door is fully open, and the safety reversing sensors are not installed, or are misaligned, the door will not close from a remote control. However, you can close the door 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32

4
Your garage door opener is equipped with features to provide you with greater control over
your garage door operation. Accessories provided with your garage door opener will vary
depending on the garage door opener model purchased.
ALERT2CLOSE
The Alert2Close feature provides a visual and an audible alert that an unattended door is
closing.
TIMER-TO-CLOSE (TTC)
The Timer-to-Close feature automatically closes the door after a specified time period that
can be adjusted using a TTC enabled door control (Models 881LM or 880LM). Prior to and
during the door closing the garage door opener lights will flash and the garage door opener
will beep.
MyQ
MyQ™ technology uses a 900MHz signal to provide two-way communication between the
garage door opener and MyQ™ enabled accessories. Your garage door opener is compatible
with up to 16 MyQ™ accessories.
REMOTE CONTROLS AND DOOR CONTROLS (SECURITY
2.0™)
Your garage door opener has already been programmed at the factory to operate with your
remote control, which changes with each use, randomly accessing over 100 billion new
codes. Compatible with MyQ™ and Security
2.0™.
NOTE:
Older LiftMaster remote controls, door controls, and third party products are not
compatible.
Accessories (Security
2.0™)
MEMORY CAPACITY
Remote Controls
Up to 40
Door Controls
Up to 2 Smart Control Panels or 4 of any other
Security
+
2.0™ door controls
Keyless Entries
Up to 4
THE PROTECTOR SYSTEM
®
(SAFETY REVERSING SENSORS)
When properly connected and aligned, the safety reversing sensors will detect an obstruction
in the path of the infrared beam. If an obstruction breaks the infrared beam while the door is
closing, the door will stop and reverse to full open position, and the opener lights will flash
10 times. If the door is fully open, and the safety reversing sensors are not installed, or are
misaligned, the door will not close from a remote control. However, you can close the door
if you hold the button on the door control or keyless entry until the door is fully closed. The
safety reversing sensors do not affect the opening cycle.
ENERGY CONSERVATION
For energy efficiency the garage door opener will enter sleep mode when the door is fully
closed. The sleep mode shuts the garage door opener down until activated. The sleep mode
is sequenced with the garage door opener light bulb; as the light bulb turns off the sensor
LEDs will turn off and whenever the garage door opener lights turn on the sensor LEDs will
light.
LIGHTS
The garage door opener light bulbs will turn on when the opener is initially plugged in; power
is restored after interruption, or when the garage door opener is activated. The lights will turn
off automatically after 4-1/2 minutes. An incandescent A19 light bulb (100 watt maximum) or
for maximum energy efficiency a 26 W (100 W equivalent) compact fluorescent light (CFL)
bulb may be used.
Light Feature
The garage door opener is equipped with an added feature; the lights will turn on when
someone enters through the open garage door and the safety reversing sensor infrared beam
is broken. For added control over the light bulbs on your garage door opener, see page 6.
USING YOUR GARAGE DOOR OPENER
The garage door opener can be activated through a wall-mounted door control, remote
control, wireless keyless entry or MyQ™ accessory. When the door is closed and the
garage door opener is activated the door will open. If the door senses an obstruction or is
interrupted while opening the door will stop. When the door is in any position other than
closed and the garage door opener is activated the door will close. If the garage door opener
senses an obstruction while closing, the door will reverse. If the obstruction interrupts the
sensor beam the garage door opener lights will blink 10 times. However, you can close the
door if you hold the button on the door control or keyless entry until the door is fully closed.
The safety reversing sensors do not affect the opening cycle. The safety reversing sensor
must be connected and aligned correctly before the garage door opener will move in the
down direction.
Operation